DISR333FTBWW General Electric Dryer - Instructions

When we first heard the screeching i thought right away that it was the belt. we ordered a new one and after i replaced it the dryer was still just as loud. I wished i went here first. Right away i found others with the same problem, did the same repair which was just taking 2 screws out, sliding the top and front panel off(watch for the electric wire connected to the panel) and replace a couple of plastic slides. now it is better than ever.

Unplugged power. removed 2 screws to take of top cover. once inside removed 2 more screws to slide front panel of. I first replaced slides on front panel. I then lift drum and installed new belt. Only trick is to make sure you wrap belt around tension arm pully properly. Basically a very easy job

First I watched the repair video on partselect.com and that really helped. It was really easy to replace the slides. I even ordered a new top bearing, old one was busted, and replaced it. Thank you for your help.

Followed the directions in the video. The only problem was there was no mention of needing a star bit set in addition to a Philips screwdriver in order to get the back splash detached from the dryer. This is probably because the machine was 11 years old. It would have been more helpful to have a note that machines prior to a certain age would need that tool. Otherwise it was a easy job even for a 75 year old grandmother.

Removed the star bit screws on the top of the control panel then removed the front by opening the door and removing the screws in the upper corners of the door jam. I then removed the top which exposed the drum slides. NOTE: This model requires 4 drum slides and NOT two as specified in the video.

Did repair as per the video except I did not disconnect wires, just swung front panel around. Only complaint...discovered parts were much more expensive than other sites.

Gently pull off all knobs and put aside. Remove the panel screws using the star bit. Tip panel forward. Remove three wires from old switch and put them on same terminals on new switch. Use the screwdriver to gently pull up the old switch's locking arm from the slot in the front panel and rotate the old switch until it pops out of the front panel. Insert the new switch into the panel and rotate until the locking arm clicks into place. Replace front panel making sure no wires are pinched. Re-install the front panel screws and control knobs.

Removed top panel giving access to drum and screws that hold front panel (door). Removed to screws to be able to remove front panel but be careful wires are short not giving you much room to remove panel. Removed plastic Drum Bearing and replaced with New one. Installed slides and put back together.

I followed the video on how to repair

had a great video to follow, made it easy to install.

The repair went very well, parts fit perfect. Now there isn't anymore complaints.

I removed several torx srews across the back control panel. Removed two philips screws under top of front dryer door. Pulled up on top surface of dryer case. Removed two more screws on backside of front door panel. Pulled front door panel forward and inserted drum slides into slots that they just popped into with a small button rod to keep them in place. The old drum slides were completely worn down or fell off. It runs like a new one again. It is over 10 years old.
The new door handle just snapped into place.
Original door handle had been broken off for several years.

With the help of doityourself guy on the internet

Popped the timer knob on and it was a perfect fit. Works great!

Unplugged the dryer. Removed the 4 star headed screws with a screwdriver. Tilted the console forward and lifted. I didn't have to slide mine to the right. Pulled the knob straight off the front of the console. Lifted the lock tab with the needle nose pliers and twisted the switch to the right. It popped right out. Pulled the wires off with the pliers. Be aware, there are three wires, two red and one black. The both red wires only connect to one terminal on the switch. It looked at first glance as if I had the wrong part. But those two wires are connected to each other so it was correct. Plugged those wires back on. Put the switch into the hole and twisted it back into place, the lock clicked in to place. Replaced the console and plugged it back in and it worked perfectly. Turned right on. This took me under 15 minutes to do. Steve is the man! This girl has been able to use his videos to repair the dryer 3 times, the washer once, and my dishwasher 3 times over the years!!