DPSQ495GT0WW General Electric Dryer - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- William from Deerfield, IL
- Parts Used:
- WE14X215
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers, Wrench set
No heat from dryer. Diagnosed by others as the Gas Valve
Watched tecnician (I paid) as he diagnosed the problem. Four screws take of the top and front. Clothes drum slides out. Access to valve is good. Valve attaches to feed via compression fitting. Male end of fitting on unit is moved to new unit via allen wrench. Drive belt is re attached around drum and over idler easily. Part cost $90.00 shipp0ed to me. Technician asked $375.00 for this repair. Access the parts via placing the model number on Google Search.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Jack from Landenberg, PA
- Parts Used:
- WE1X1263
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver, Screw drivers
Old knob would not turn shaft and dryer would not start. Cracked in center.
Turned off breaker, rmoved back panel, removed timer, replaced knob. Put back together.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- John from Andover, NJ
- Parts Used:
- WE1X1263
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Knob had cracked inside
Just pulled off the old knob and pushed the new one onto the switch. Done in 1 minute.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- starla from Fort Cambell, KY
- Parts Used:
- WE1X1263
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Pliers
Knob was broken off ordered a new knob.
First the old knob was broken just pulled it off. made sure the metal piece was clean of all debris or junk and slide the new know on turned it to make sure it was snug and was ready to go. to easy
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Tony from POTTSVILLE, PA
- Parts Used:
- WE4M181
- Difficulty Level:
- Easy
- Total Repair Time:
- 1- 2 hours
- Tools:
- Nutdriver, Pliers, Socket set
Heat thermostat,now replacing the drum bearing with your kit..
By watching your video which was very helpful as I never made this repair before. All worked out fine. Since then I have ordered other parts., (drum bearing kit, door slides and a new belt.) The video on replacing the drum kit is very helpful too. One other fact is prices beat all other sites I looked and when I'm done the dryer will be "rebuilt" I recommend your parts to everyone., they are great quality.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Cheryl from Inwood, WV
- Parts Used:
- WE03X37318
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers
Making noise while drum was turning.
Removed 2 screws to remove top. Removed 2 other screws to remove front. Removed old parts. Installed new parts. Reassemble all afetr cleaning duct work out.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- krisy from anniston, AL
- Parts Used:
- WE1X1263
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Dryer timer knob would not work
Easy! Just took the broken knob and metal ring off, and put on the new knob. took less that one minute. Works like a charm now. No service call cost either!!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- GUY from BEDFORD HILLS, NY
- Parts Used:
- WE03X37318
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
Drum slide wore - damaged drum bearing
r/r parts unit runs great
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Kelly from Hendersonville, TN
- Parts Used:
- WE03X37318
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
Loud squeaking noise
Repair was VERY easy - 4 screws total! Used google to find a video online that showed the steps.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- David from santa maria, CA
- Parts Used:
- WE03X37318
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
squeaking
snap in snap out
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Jeremy from Wexford, PA
- Parts Used:
- WE03X37318
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
Loud squeaking sound from dryer drum.
Initially purchased just the plastic slides, but when I opened the dryer I found the top drum bearing was smashed and the plastic was basically gone in a whole section, so I then ended up ordering the bearing as well. If you hear the loud squeaking, just buy the top drum bearing and the 4 slides (two white and two dark green). It is an easy repair and the squeaking sound is gone.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Robert from Big Rapids, MI
- Parts Used:
- WE03X37318
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
bearing and slides worn out
took off top of dryer, took out 2 screws so front of dryer could be removed, replaced bearing,slides and felt seal
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Steve from Dallas, TX
- Parts Used:
- WE1X1263
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Dryer's timer knob broke on the inside
When I got the knob in the mail, I opened up the package, made sure the knob was identical to the broken one and pressed the new knob into place. I needed no tools to put the new knob on. It was easier than I thought.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Richard from Williston, VT
- Parts Used:
- WE03X37318
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
Dryer squeaks and squeals while running
Took the top of the dryer off by removing two philips screws in front. Removed two screws holding the front of the dryer on. Pulled the front out enough to reveal the worn drum slides. Replaced them. Reassembled.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Julie from Sterling Heights, MI
- Parts Used:
- WE03X37318
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
worn dryer drum slides
i first popped off the top of te dryer after removing the two screws in frotn when you open the door. I then removed the two screws holding the front together. after tilting the front out i was able to place the slides in without having to pull of the front entirely.
Was this instruction helpful to you?
Thank you for voting!