DPSB519EB0WC General Electric Dryer - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Robert from Big Rapids, MI
- Parts Used:
- WE03X37318
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
bearing and slides worn out
took off top of dryer, took out 2 screws so front of dryer could be removed, replaced bearing,slides and felt seal
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- DUANE from Kutztown, PA
- Parts Used:
- WE03X37317
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers
Loud Banging, not drying.
First I got the front bearing, found out I needed the slides too. It was binding at first, so I undid an earlier misadjustment I made (on the back drum mount). and it works!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- ROB from CLARKS SUMMIT, PA
- Parts Used:
- WE03X37317, WE03X37318
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers
Loud noise when running
I was teaching my associate how to do this repair so I showed him how to take off the top of the dryer. Then I showed him how to replace the drum slides. I had him clean out the dryer since we had it apart, and I also showed him how to remove the drum and then reinstall it. This was a very easy repair, and he learned a lot that he otherwise would not have known. Thanks for getting the parts to me so quickly. Rob from Clarks Summit.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Mark from Montrose, CA
- Parts Used:
- WE4M275
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Pliers, Screw drivers
Dryer wouldn't heat
Had a repairman tell me I needed a new controller for about $350 so I decided to do it myself...found the schematic and tested the termisters. One of them was much lower than the range so I ordered a part of the web (here)...The diagram shows the thermistor and the safety switch so I ordered the wrong part (out $40). Ordered the other part which turned out to be the thermister. Took two weeks to get through this..Sure enough it worked!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Keli from Manassas, VA
- Parts Used:
- WE03X37317
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 1- 2 hours
- Tools:
- Screw drivers
Dryer made hig-pitched screech
Took off the top and front of the dryer---really easy, just two screws for each. Put new drum slides (4) on the front/sides of the drum. Then things got a little bit more difficult. Removed the drum entirely, vaccuumed everything out and had to replace the rear bearings. My husband did this part so I can't tell you exactly how he did it. Not too difficult though. The written directions from here were hard to read---need to make a new copy from the original as it's so copied that it's all smudged. Anyway, once we got the new bearings on, we put everything back together. Dryer works like a charm, at a fraction of the cost it would have been to get someone out to do it. Thanks a bunch for the fast service!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- George from Lynchburg, VA
- Parts Used:
- WE03X37318
- Difficulty Level:
- Easy
- Total Repair Time:
- More than 2 hours
- Tools:
- Nutdriver, Screw drivers, Socket set
Drum squeaked and occassionally would not turn, even though the motor ran.
I ordered and replaced the front and rear bearings, including the slides that go on the front bearing. Most of this was un-necessary; replacing the slides would have been sufficient, and much easier to do. Two of the old slides were worn completely away.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- christopher from flushing, NY
- Parts Used:
- WE01X20419
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
door handle to dryer broke...got part in 2 days,took 2 seconds to fix.
just 4 slots where the handle goes. Snapped handle into slots, good as new.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Claire from Blue Bell, PA
- Parts Used:
- WE01X20419
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Handle broke
It clicked right in. Thank you!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Charles from Mocksville, NC
- Parts Used:
- WE01X20419
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Ddoor Handle Broken
Pulled broken one out and inserted new one in slots and popped in place.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Barbara from Camarillo, CA
- Parts Used:
- WE01X20419
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
door handle of dryer broke off
It just popped back in...the really really amazing thing is the part arrived the next day....and I could immediately get the dryer fixed..thank you so much...
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- James from San Diego, CA
- Parts Used:
- WE01X20419
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
door handle broke
Actually, my wife just unscrewed the part that was still there and screwed on the replacement handle: it was easy for her. Thank you for having the part!...James
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Kelley from College Station, TX
- Parts Used:
- WE01X20419
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Broken dryer handle
The part arrived 24 hours after I placed the orer, even with the standard shipping. I just popped it in and problem solved.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Ray from Maplewood, MN
- Parts Used:
- WE01X20419
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
plastic door handle broke
The service was prompt and efficient. When the door handle arrived it was very simple to attached. it snapped right into place that was it. It took just a few moments.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Shauna from Bend, OR
- Parts Used:
- WE03X37318
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
High Squeaking noise
I removed the top of the dryer and saw that the top two drum slides where gone and the drum bearing itself was damaged I Temporally placed the parts on the drum bearing until I got the new one, that stopped the squeaking noise. All I needed to do was place the part with the hole on the little hook and then sled the other part in its slot.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- phillip from denver, CO
- Parts Used:
- WE01X20419
- Difficulty Level:
- Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Pliers
none
Snap in place
Was this instruction helpful to you?
Thank you for voting!