DPSB519EB0WC General Electric Dryer - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Mike from Desert Hot Springs, CA
- Parts Used:
- WE03X37317
- Difficulty Level:
- Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
squeaky drum
The gentleman knew what the problem was, sent the right part, and I looked like I was smart.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Cheryl from Inwood, WV
- Parts Used:
- WE03X37318
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers
Making noise while drum was turning.
Removed 2 screws to remove top. Removed 2 other screws to remove front. Removed old parts. Installed new parts. Reassemble all afetr cleaning duct work out.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- David from Lawrenceville, GA
- Parts Used:
- WE03X37317, WE03X37318
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
Squeaking and black marks on clothes.
Unplug the dryer. Remove top panel (remove two screws on the upper inside edge of the dryer door). Lift the front panel from front (tabs and slots at the back) and lift off. Remove the front panel (remove a screw from each side - top/front). Front panel sits on two feet at the bottom, tilt it forward from the top and lift it up (careful not to damage the electrical connection at the bottom left side). I found the dryer had another damaged part (plastic guide that the Slide WH and the Drum Slides connected to was badly worn). After ordering the additional part I attached the slides (white and gray) to the guide. Set the front panel back on the two feet and tilt it back into place (you'll need to slightly raise the drum back into position - easy). Replace the two screws that connect the front panel. Replace the top cover. The whole repair took less than 1/2 an hour including the time it took to vacuum out the dust. Total cost, about $35!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Dave from Wallingford, CT
- Parts Used:
- WE4M137
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Pliers, Screw drivers
Dryer would shut off on heat dry after a couple of minutes. I could feel the heat working. It would only continue to run on fluff/no heat
Pulled the drum an found spade clip burned on wire. Hi limit Thermostat crumbled/ broke while pulling spade clip so I trimmed back the wire, cleaned the spade clip and soldered the wire back on. Isolated the other thermostats in the system and tested for resistance. Reassembled dryer.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Craig from St Johns, FL
- Parts Used:
- WE01X20419
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Old Handle had broken
inserted on an angle and snapped in place.
The best part of this story was I ordered the part on a Saturday and got it on Monday evening.
The repair took less than 20 seconds. I am extremely impressed with the fast fast fast shipping time.
The best part of this story was I ordered the part on a Saturday and got it on Monday evening.
The repair took less than 20 seconds. I am extremely impressed with the fast fast fast shipping time.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Michael from Lumberton, NJ
- Parts Used:
- WE01X20419
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Plastic door handle broke
Snapped on new handel. Took all of 5 seconds. The hardest part was finding the part, which your website took care of....Thanks!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Sharon F from Washington, UT
- Parts Used:
- WE01X20419
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Door handle broke off...
Snaped the new handle back on...no tools needed,
just fit the plastic groves of the handle into the holes on the dryer door. Very simple!
just fit the plastic groves of the handle into the holes on the dryer door. Very simple!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Jamie C. from North Hollywood, CA
- Parts Used:
- WE01X20419
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Dryer door broke off.
It was so easy, I just depressed a couple of tabs and it popped right in!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Darlene from North Brunswick, NJ
- Parts Used:
- WE01X20419
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Broken Door Handle
I just snapped the door handle on the dryer in less than a minute. I am completely satified. Did I mention I received my part in one day. I ordered online before 3pm and received it the next day before 11am. Very impressed. Thanks PartSelect!!!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- James from Cumming, GA
- Parts Used:
- WE01X20419
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Just cliped it in the holes
I broke the handle
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Wayne from Fort Washington, PA
- Parts Used:
- WE03X37318
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Squeeky Noise When Dryer Was Running
First I removed the 2 screws that hold the lid down. Then I pulled the lid off. Then I removed the 2 screws that hold the front of the dryer in place. Then I lifted the drum a little and pulled the front cabinet out a little so I could see the drum slides. I removed the bad drum slides and installed the new ones. I then put everything back together and turned on the dryer. The squeeky noise was gone.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Don from Peoria, IL
- Parts Used:
- WE03X37317, WE03X37318
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
the dryer had a lovely squeak
I took out a whooping four (4) screws, two that held down the top to the front panel then two screws that attached the side panels (at the top) to the front panel, raised the drum from the inside, leaned the front panel foreword, popped out the old slide (there was only one left), installed the four new slides & put it back together. That's pretty much all there was to it, vary simple.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- MITCHELL from LAFAYETTE, LA
- Parts Used:
- WE01X20419
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
handle broke due to pulling on door
just put new one on. no tools needed fits in holes already there. handle just snaps on,
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Alan from Crest Hill, IL
- Parts Used:
- WE01X20419
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Dryer Door Handle broke
This one is so easy my grandson could do it. The removal was easy, it broke off. The installation was a "snap in place". Thinking I needed a few days of dryer use without the handle, I made a temporary repair. I fished some heavy packing string thru the slots in the door, made a loop, than a knot. This gave my wife something easy to grab to open. Did not even need to do the temporary repair, the part arrived in one day.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- shelly from layton, UT
- Parts Used:
- WE01X20419
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
The plastiic door handle broke off my GE dryer
As soon as the new door handle arrived, I just snapped it into place. It took about two seconds>
Was this instruction helpful to you?
Thank you for voting!