DCCD330ED2KC General Electric Dryer - Instructions

Snap out the broken part. Snap in the new part. Use caution with the wires, but don’t have to disconnect them.

good replacement procedure on you tube.

started with replacing the belt and tension pulley which I purchased from another source. I found your videos on line and they are great. easy to follow. Realized I needed the bottom vent assembly and your prices were better than my local supplier. It was easy to replace thanks to your video. It was nice that you included it in the final order status. The only problems. Did not know the duct felt seal was included with the new duct assembly. I ordered the wrong bearing slides, web site showed both green and white for my model. I now realize I should replace the upper bearing housing. Can I return the unused parts, unopened and have that put as a credit to my next order? Thanks

On my GE Dryer the lint filter is located inside the door at the bottom. The filter can just be pulled out by hand & a new one pushed into place

First I replaced the timer, but dryer still did not start. took apart dryer, jumper out door and componet near motor to see what problem was and to be able to run dryer while opened up. Actually motor had seized up just enough to not allow motor to start rotating. Lubricated motor shaft and rotated motor for oil to work its way in. Tried starting again and motor started. Buttoned dryer back up and reconnected wires to appropriate places and started dryer again and again.Worked for 4 loads of laundry and still working for 3 loads on Wednesday. Working fine

Replaced new screen in place of old one.

Wife was out of town, visiting family. I broke the door strike by wedging the dryer door between the laundry room door, closed the laundry room door and it snapped the door strike breaking it. I ordered the part, and it shipped fast using the standard shipping, nothing fancy. Grabbed a pair of pliers and pushed the new door strike into place. It snapped right in, fits and works perfect like nothing ever happened. The wife will never know :)

Watched the video on a different style of dryer so taking apart a bit of a challenge. The old Front Drum Bearing was completely gone on left side and a challenge to pry it off the front dryer panel. replaced felt seal and front drum bearing. noticed that there was 4 places for new bearing slides. the ones i ordered were white and green but did not know why or which one went where as no explanation with packaging. also only ordered one of each and so now had to stop and try and find two more. ! hour later i had brought back a tupperware lid that was thick enough and stated could go to 194 degrees F. i cut out one replacement for green bearing and reused the old white one since it was in good shape from right side of drum bearing. i went back to this website and noticed in the comments section for drum bearing that someone stated the green bearing slides go in at positions 11 and 1 and the white at 10 and 2. they are different materials and having more weight of drum on green now made sense. put machine back together and told neice to keep eyes and ears on dryer thru cycle. she did not even know it was running just in next room.

was no repair- removed filter from door and installed new filter into door. No tools required.

When the dryer was installed last year by the dealer, one of the hot leads was not screwed down tightly. Over time the screw loosened and began to arc causing the plastic holding the screw to melt. When I moved the dryer the hot lead fell off and hit the terminal block cover shorting out the dryer. I was able to locate the exact terminal block I needed with their helpful dryer section diagrams. The part came in the time they said. I took off the old terminal block with just 2 attached screws. i kept track of which screws held the hot and neutral conductors and the ground before I removed them. I was then able to slide on the dryer wires and attached the home conductors. I put on the cover plate, turned on the circuit breaker and it worked.

Our gas GE "Eterna" King Sized capacity dryer started squeaking one day. I was suprised since the dryer was only a few years old, but assumed some grit had invaded and worn a bearing in the belt tensioner. My wife and I have three kids, so we use the dryer daily. The sound got louder quickly and finally it was so loud I had do something. After unplugging the appliance I took the top off the dryer (two screws in the top of the door jam) and the front off (two screws at the top of each corner) and in doing so saw that the drum bearing, which is just a round plastic
"shelf" on which the tumbler drum rides, suspended over the door, was worn through. There were four little "slides" on the bearing surface, and all but one was worn down to dust. I ordered the replacement bearing and slides (two white, I didn't know I also needed two green and have since bought them too) from Part Select and they arrived in about three days. In the meantime I re-assembled the dryer easily and we did use it once or twice, shrieking. When the parts came in I installed them in about 20 minutes, screwing the new bearing onto the rear surface of the front panel, right over the opening for the dryer door. The dryer has worked perfectly since. I used one Phillips head screwdriver for the whole job and paid about $50.00 for the parts. I work in an office and I travel, and when I was a kid I fixed my own cars and stuff, but I'm no appliance repairma! Nevertheless, this was easy! I assume I saved at least $100. The dryer works perfectly and more importantly, it's quiet again!

After unplugging the dryer, I removed 2 metal screws up under the dryer sill rim, and removed the dryer top. Then, removed two more at the top of the front (door) section to remove it.

I wasn't careful enough when removing the door, and the wiring connectors popped loose from their connections. No harm done, though. Disconnect the wires once you remove the front panel.

I had to loosen the bottom metal screws on one side panel to have enough give to pull the dryer drum out.

The only way to replace the belt is to bend over the side of this unit and with one hand put the belt around the motor drive shaft, pull the tension pulley back, and put the belt on the wheel.

The hard part is working the drum back into place while VERY carefully slipping the belt into the drum goove. Many attempts were made only to have the belt slip off of the tension pulley or motor driveshaft. Be care full to turn the drum clock wise if the belt twists while working it into the drum groove. It was very disappointing to finally get the belt on, and work the drum back into place only to discover I had twisted the belt with the smooth side making contact on the driveshaft. Thus, I started over.

Aiming the drum into the back of the dryer is a tough task. I recommend a 1" X 4 " X 12" board to slip under the drum when beginning this process to help stablize, and guide the drum. It helped me tremendously, and was easy to remove out from under the drum once everything was back in place.

Use gloves. Yes, tough to work with in small places, and I did take them off to replace the belt around the tension pulley, however, there are too many sharp edges on the metal body of the dryer and especially the drum to do so without gloves.

Wires were easy to reattach and reassembly was smooth except for the top...check out the tabs, and spring tabs before you try and just plop the top back on. It goes a certain way...You'll know what i am talking about when you do this task.

I truly hope you have L O N G arms to do this task, and that the new belt lasts a long, long time!

I first watched the video on how to. Being mechecanically inclined I dismantled and removed everything needed to replace the drum bearing. Also removed belt at the same time. I replaced the bearing, then the belt. The belt could be a little tricky for some people. Getting the belt on the tension pulley could be a problem. What I did was I got a large nylon tie and put it around the armature of the motor. I then retracted the pulley just enough to be able to slip the belt over it. Of course this is all performed through the limited space on the bottom left, between the drum and the dryer shell. Once on the pulley, I cut the tie with wire cutters and it snapped into place. Rotated the drum a couple of times to line the belt with the pulley, perfect. I then put everything back together. I also cleaned any and all the lint that had gathered throughout the exhaust. Pluged the dryer in, perfect. Just like new. One more note getting the parts was so easy also. Your website and how to demo was a great help. Thank you, thank you very much. The words of the late Elvis Presley. They never get old.

Unscrewed the old, screwed in the new making sure wires matched up same as before. Reset my breaker and works like new again.

I read the repairs that others had posted and how they did it. It was really easy. My only complaint is that I didn't know that I needed the slides that attached to the bearing and couldn't find them on the repair list. My dryer had a spot for 4 of them and only 1 was left. Otherwise, being a female, I felt great to be able to fix it myself! Thanks!
Let me also say, I only have one good working arm/hand.