GTDP450ED2WS General Electric Dryer - Instructions

I used a flat head, a phillips head, and two sizes of sockets with my screwdriver to complete this project. I initially undid the control panel, but I don't think I needed to. I next took out two long screws that were holding the top of the cabinet on. These screws were just inside the doorway, directly above where the door sits when closed. I took the top off and set it aside. Being careful to mark which wire went to which lead, I undid the leads to the door open/closed switch. I next found two, black, hex-end screws, one each on the upper sides, towards the front, and undid these with a socket end on the screwdriver; being careful not to drop them as they came out. I then tilted the front panel out and up and set it aside. Note that the front opening holds the drum up so it can spin. Next, I tilted the front of the drum up, and pulled it outwards, till bearing at the back pulled out of the socket, and the drum dropped down enough that I could push the belt off the back of the drum. I then pulled the drum out through the front opening. I could see that the bearing was mostly worn away and metal was rubbing on metal. On the drum, I took off the air diffuser and the drum's half of the bearing assembly, and attached the new part of the bearing assembly, where the old one was. There was a metal disk that I was careful to reinsert in its former spot. I tried to make sure that all screws were tightened with equal force. Then I removed the entire bearing housing/blower assembly by undoing the outer screws that attached it ti the back wall of the cabinet, I rotated it outward at the top , pivoting around the compression fitting (no screws) at the base. I then removed the back half of the bearing housing, and replaced it. I needed to screw in the screws from the front while holding the spring-clip-thing in place (once installed, you can stick your finger through the hole in the bearing housing and feel the clip right behind it). I took this opportunity to clean all the excess lint out of the cabinet. I then replaced everything in reverse order until I got to the drum. I put the belt loosely arounf the drum, with the grooved/ridged side facing in. Then put the bearing (with drum), back in the socket. Feeling through the hole under the front of the drum, take the belt where it hangs off the drum TO YOUR RIGHT, run it under then up around the left side of the small pulley, then pull it to the right (above the small pulley) and around the right side of the big (tensioner) pulley, and let go. Note that there is a swithch in the tensioner that won't switch on unless there is enough tension on the belt! Put the front back on, lifting up the barrel from the inside, so that the barrel opening slides around the outside of the front's assembly. Ours seemed to fit more tightly than it had previously, into the felt padding around to bottom of the front assembly, but it seems to work fine? Screw in the two black, hex-head screws from the sides into the front, and re-attach the door-switch wires. Turn it on (carefully) to make sure it runs. Then attach the top, using the two long screws up through the door opening into the top. Ours is working much better than before - hotter, faster, quieter! Should we have lubricated the bearing with lithium grease?

I removed the top cover and the back cover to install new belt.
Once i put new belt i discovered that the pulley was also broken so now i have order the pulley so that i can complete the repair

Key starting point is to remove top cover by removing two long screws located at the front of the cover
Remove control panel and it's bottom and side supports.
Remove short vent pipe by bending retainer tab.
Support the drum at the top using piece of rope.
Remove main rear cover (leave bottom attached).
Remove electric heating unit and install new bearing carrier from kit.
Reinstall the the heating unit
Remove three screws (inside the drum)to release the inner drum cover and release the bearing carrier.
Install new bearing carrier. Note: the three holes in the bearing carrier are not tapped, I suggest that the screws be installed (threads cut) into the bearing cover before attempting to install the bearing carrier.
Install the new bearing carrier. Note: pilot one of the holes using a small nail etc. then go on to install screws in the other two holes remove the pilot device and install the third screw.
Reassemble in reverse order.

After speaking with your representative and him explaining how to me how simple it would be to switch out this light socket myself. I went on y tube went through the instructions and had to go buy a new dryer. And before you jump to any conclusions I can and do repair and and all of things around my house. I will NEVER purchase anything from you company again ander the pretense that it is so simple. This should have been told to me that an election should have done the job!!!!!! Now not only am I out the money I paid your company but I’m out the money I shelled out for a whole new dryer. I am a very angry customer and I would never recommend you to anyone!!! EVER!!!

Shortly after a piece of felt (the duct felt seal) was visible on the drum intererior, the dryer started making metal-on-metal squeaks. A few weeks later it started leaving'machine part' type brown/black marks on clothes. With the model # it was quite easy to find and order the correct part, which arrived a few days later. The accompanying video made installation quite straightforward, even for someone who's NEVER worked on a dryer before - even though the model used wasn't the same. Over half the repair time was to clean out lint and dirt from the various exposed parts. Overall, an easy and effective repair that solved the staining issue. Follow the video and you won't go wrong.

Handyman installed the finally correct switch. It was not the starter button.
This company was wonderful. Replaced each part without charge and rushed the replacements to us. Can' say enough good things to thank them for their courtesy.

I followed the instructions from the video removing one wire at a time and set them in place when they were all in I put the timer back and used the dryer

had a great video to follow, made it easy to install.

Still waiting for your parts. over two weeks to get part which was a hinge for something, I don't know what, but not my dryer seal. You said you would refund shipping and wrong part and charge me for a new order. End result was I got charged extra shipping for your mistake. The part still is MIA and it has been 5 weeks since I originally ordered. Will never do business with you again.

First I replaced the timer, but dryer still did not start. took apart dryer, jumper out door and componet near motor to see what problem was and to be able to run dryer while opened up. Actually motor had seized up just enough to not allow motor to start rotating. Lubricated motor shaft and rotated motor for oil to work its way in. Tried starting again and motor started. Buttoned dryer back up and reconnected wires to appropriate places and started dryer again and again.Worked for 4 loads of laundry and still working for 3 loads on Wednesday. Working fine

the pulley spring took so much pressure to hold it down it took 3 men and a boy to hold it and place it in position to to get the belt on. Also there is not enough room to get your arms and hands in without getting some small cuts.Ultimately I removed the screws in the back of the dryer and spread the side of the dryer out to gain proper access. It was an easy repair if the spring would not have been so strong.

On my GE Dryer the lint filter is located inside the door at the bottom. The filter can just be pulled out by hand & a new one pushed into place

Removed too of dryer and placed the parts on. Runs like a brand new one. Thanks so much!

Replaced new screen in place of old one.

Pulled the knob out of the package,went downstairs to basement, put the knob on the dryer, walked away with a fixed product. Took 5 minutes.