Models > GTDP350EM1WS > Instructions

GTDP350EM1WS General Electric Dryer - Instructions

Jump to:

All Instructions for the GTDP350EM1WS
76 - 90 of 702
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Customer:
GLENDA from BLNG SPG LKS, NC
Parts Used:
WE4M416
Difficulty Level:
Very Easy
Total Repair Time:
Less than 15 mins
Tools:
Screw drivers
DRYER WOULDN'T START
My dryer knob broke on the timer cycle switch so I ordered a new one along with a new dryer knob which didn't fix the problem, then I ordered the start switch and all I had to do was remove the back of the dryer where all the knobs are located and remove the start switch by turning the start switch to remove it, replace it with the new one by turning it till it clicks in just like when you removed it, put knob back on the front. However that didn't fix my dryer either so I ordered the thermal fuse and switched it out and that was what started the dryer back up. It is located on the back all the way to the bottom where the electrical cord is. Remove the cover and locate the fuse. Use a pair of pliers to pop it out and push the new one back in.
12 of 22 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
Stephen from FISHERSVILLE, VA
Parts Used:
WE09X27634, WE03X37317, WE3M26, WE03X37318
Difficulty Level:
Easy
Total Repair Time:
30 - 60 mins
Tools:
Screw drivers
Dryer was making loud noise
Upon receiving the parts, we went to the video repair instructions. We found these videos to be very well done and very helpful. It was great being able to pause the video at specific points until we were able to complete that step of the repair. All of the replacement parts fit correctly and there were no issues.
7 of 7 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
Brad from DELAVAN, IL
Parts Used:
WE4M415
Difficulty Level:
Easy
Total Repair Time:
30 - 60 mins
Tools:
Pliers, Screw drivers
Dryer would not start.
First unplug dryer to prevent electrical shock. To remove the front of the dryer, open the door in top left and top right corners is a machine screw. They can be removed with a Phillips screw driver. Lift the top slightly and let front fall forward about 6 inches, lift slightly. Two wire will be connected to the switch in the door. remove the wires and squeeze the tabs on both sides of the switch and push it out. Push new switch in to replace old switch and reassemble.
7 of 8 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
Cheryl from Old Town, FL
Parts Used:
WE01X20419
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins
Broken Door Handle
Clips on the inside of the door handle had snapped off, 1 minute later it worked like new. NO TOOLS required! So happy my older appliances can have new life by the parts carried by PartSelect. Thanks!
8 of 12 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
Angela from Richmond, KY
Parts Used:
WE01X20419
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins
broken dryer handle
My husband broke the door handle, but of course, i had to be the one to order the part & fix it. I ordered the part on the weekend and much to my suprise it was on my doorstep on Tuesday when I got home from work. Then I saw the part was shipped from nearby Louisville. I was overly happy with partselect!!!!! All I did was open the packaging and clip the dryer handle into the 4 holes. Easy as pie!!!!
6 of 7 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
Al from Elmhurst, IL
Parts Used:
WE03X37318
Difficulty Level:
Really Easy
Total Repair Time:
15 - 30 mins
Tools:
Screw drivers
The Front Drum Glides wore out
I first unplugged the unit, opened the top, disconnected and took off the control panel, took off the front panel to determine the source of the squeaking noise coming from the Dryer. I saw that 3 of the 4 Front Drum Glides were gone and the drum had worn away significant amounts of plastic from the Top Bearing Assembly. I purchased the Top Bearing Assembly and a set of 4 Front Drum Glides. Disassembled the damaged parts and reassembled with the new replacement parts. The reassembly took less than 20 minutes. I plugged in the Dryer and viola! It works as good as new.
6 of 7 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
Teresa from Brighton, MI
Parts Used:
WE09X27634, WE03X37317, WE03X37318
Difficulty Level:
Really Easy
Total Repair Time:
15 - 30 mins
Tools:
Nutdriver
Noisy
Took apart by removing the top and front panel. Found drum rubbing due to worn glides and felt.
7 of 10 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
Kevin from HENDERSON, NV
Parts Used:
WE03X37317, WE3M26, WE03X37318, WE1M462, WE1M461
Difficulty Level:
Really Easy
Total Repair Time:
30 - 60 mins
Tools:
Nutdriver, Screw drivers
Loud sqeeking.
I followed some simple instructions from GE. It was really easy and I even found some spare change inside the cabinet which my wife took off my hands. :/
6 of 7 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
Tom from WILLISTON, ND
Parts Used:
WE04X20089
Difficulty Level:
Really Easy
Total Repair Time:
30 - 60 mins
Timer appeared to be broken. Turned all the way around without contacting anything.
Ordered new timer with overnight delivery and thought all was well. Replaced timer and still didn't work. Am embarrassed to admit all was wrong was that the timer knob was broken and spun around. But am typing this so someone else might check the knob first of all before going to all the trouble of replacing the timer. Although it was an easier job than I thought. About 15 minutes after I got the dryer pulled out. Oh well, have a new timer and knob now and got to clean out behind the washer and dryer which was needed and the dryer vent also. All is well now!
6 of 7 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
STAN from UPPER ARLNGTN, OH
Parts Used:
WE1M1011
Difficulty Level:
Very Easy
Total Repair Time:
Less than 15 mins
Tools:
Screw drivers
Plastic housing for the door latch mounted in the chassis of the dryer was damaged so the section of the latch in the door wouldn't align.
This kept the interlock open and shut off the dryer when the door swung open The broken latch was popped out using a flat blade screwdriver and the replacement snapped into place by hand. Good as new!
5 of 5 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
Brian from Bossier City, LA
Parts Used:
WE3M26, WE03X37318
Difficulty Level:
Easy
Total Repair Time:
15 - 30 mins
Tools:
Screw drivers
Loud squeak at regular intervals
First, I removed the 2 screws for the top panel, lifted the top panel off, then I removed the 2 screws holding the front panel, tilted it forward to clear the drum, disconnected the door switch and set the panel aside. I then installed the 4 slides on the new front bearing, removed the light socket from the old bearing, removed and discarded the old bearing. I installed the light socket into the new bearing and the bearing assembly snapped into place on the front panel. I then re-connected the door switch, aligned the front panel with the drum, secured the front panel with 2 screws, then carefully placed the top panel back in place and secured it with 2 screws. I checked the rotation of the drum and it worked like a champ. Matter of fact, that same day I put this dryer and a matching washer up for sale at 8:30 am on October 31st and by 9:20 am I already sold them!! I delivered and hooked them up and the dryer works great!!!
5 of 6 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
Jason from CYPRESS, TX
Parts Used:
WE14X25080, WE3M26
Difficulty Level:
Really Easy
Total Repair Time:
30 - 60 mins
Drum bearing and Lint Chute plastic was cracked.
The video of the dryer lint chute assembly showed the man without gloves. I didn’t wear gloves. When I disconnected the wire from the front panel assembly, my hand jerked and hit the side of the panel. It must have been razor blade sharp, because I got a deep cut. Advise people to wear gloves to protect hands from sharp metal.
5 of 6 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
philip from pickens, SC
Parts Used:
WE03X37318
Difficulty Level:
Easy
Total Repair Time:
1- 2 hours
Tools:
Nutdriver, Screw drivers, Socket set
Replaced Drum Bearing Front And Rear
Pulled the unit all apart to replace the rear drum bearing. Also replaced the front bearing. Works like brand new. Easier then I thought
5 of 6 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
gerard from goldsboro, NC
Parts Used:
WE09X27634
Difficulty Level:
Easy
Total Repair Time:
30 - 60 mins
Tools:
Nutdriver, Screw drivers
the felt in front door worn out
i follow your video and all went well except now the dryer will not heat. i went back on your site an tried the no heat option an still no heat
6 of 9 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
Patty from PHILA, PA
Parts Used:
WE1M964
Difficulty Level:
Very Easy
Total Repair Time:
Less than 15 mins
Tools:
Pliers
The timer knob cracked and would not turn on.
I followed your instructions. Removed the old knob. Used pliers to get inner pice off as the new knob has that little metal washer thingy in my new replacement knob. Thanks I am happy you save me money.
4 of 4 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
All Instructions for the GTDP350EM1WS
76 - 90 of 702