GRDN510EM2WS General Electric Dryer - Instructions

Son found out where the bulb was by using YouTube. I googled lamp for model number and your website came up. I ordered the part, it arrived promptly, and my son installed it.

stuck it back in the holes just like the original handle. Had to do a little adjustment because I put screwdriver in them too many times to open the door after the original handle feel off, so the fit was loose. Fixed with tape.

I read the other repair instructions on this site and looked at the parts diagrams. It wasn't entirely clear how everything came apart but once I started by unscrewing the top of the dryer and removing it (screws were just inside the dryer door) it was easy. Unscrewed the front panel next , swung it out, and it was quick work to install the new bearing with the slides. It wasn't too clear in the parts diagrams but I did need two each of the dryer drum slides and front dryer drum slides, four total, two on each side of the drum bearing. The dryer had been running on the old drum bearing itself, the old slides had worn completely down and the bearing itself was starting to disintegrate too. If I'd caught it sooner I could have reused the bearing and just replaced the slides. Saved a lot of $ and the dryer is nice and quiet again!

Will you replace the dial mechanism for the timer. In fact my wife replaced ours had it done by the time I got home.

Removed panel and replaced each wire one by one. Slide timer into bracket. Reinstalled panel, put knob on and resumed normal operations.

this was a part i ordered for future use. i was very happy with the ordering process and speed of delivery from PartSelect.

inserted the lint catcher into the opening to replace the old one

I order the parts needed to replace the slides, the felt ,and the bearing on a Sunday afternoon. The parts arrived on Tuesday even though I used regular shipping. I followed the instructions posted by another customer. It was extremely easy and only took me about fifteen minutes. My only problem was that I needed 2 each of the front slide and the rear slide, and I unknowingly only ordered 1 of each. I order the other 2 on Tuesday via regular shipping and they arrived on Wed. AMAZING!!!!

When we first heard the screeching i thought right away that it was the belt. we ordered a new one and after i replaced it the dryer was still just as loud. I wished i went here first. Right away i found others with the same problem, did the same repair which was just taking 2 screws out, sliding the top and front panel off(watch for the electric wire connected to the panel) and replace a couple of plastic slides. now it is better than ever.

Unplugged power. removed 2 screws to take of top cover. once inside removed 2 more screws to slide front panel of. I first replaced slides on front panel. I then lift drum and installed new belt. Only trick is to make sure you wrap belt around tension arm pully properly. Basically a very easy job

Drum was misaligned and scraping againt the appliance housing due to worn-out slides.

Replaced the drum slides 2 - white, 2 - black. Replaced the slide housing (front drum bearing?). This part was worn due to worn-out slides that were missing.

Cleaned out old lint from rear of drum and appliance housing. Put new weather stripping seals on the lint catch exhaust. Checked drum belt for cracks and checking.

Buttoned everything back up and dryer works as good as new. $60.00 for parts, 1 hour labor and the job was done!

I followed the video on how to repair

Removed top - 2 screws. 2 more and the front comes off. I left the wires connected, and leaned the front against the wall. I then popped the drum bearing, with the slides off of the front, and pulled the felt from the lower half. I took some extra time cleaning lint with a shop vac. I then assembled the new parts back onto the front, and pulled the felt into position - it was a little fussy getting it right. The front panel and the top go back, and it`s done. I am glad I ordered the drum bearing, as the felt was worn much more than I would have guessed. This job could probably be done in 15 minutes next time, not including lint clean-up.

The instructions that came with the bearing were limited and the illustrations were too dark to see. However, after reading the reports of others on this website, the repair was very easy.

Prior to disassembly, remove theaccess panel on the rear of the dryer. Pull the belt drive pulley arm up and the belt will easily slide off of the motor pulley. The belt can be left on the drum.

Then, remove two screws at the inside top of the dryer door. The top of the dryer will then lift up at the front and slide forward to remove. This will allow you access to two bolt head screws on each side of the front panel. Remove these two screws and then lift the panel slightly up and forward. The front panel will then be free and the dryer drum will slide forward and out. Remove the four bolt head screws (behind the electric elements) from the heater element on the inside back of the dryer box.

You can now exchange the bearing on the drum and the bearing insert on the dryer heating element simply by removing the old and reinstalling the new just as the old was removed - four screws for each.

You will need an assistant to re-install the bearing. Someone needs to hold the three pieces behind the drum as you insert the three screws. You'll also need a star wrench set for this.

The drum is easily reinserted - just be careful to get the front of the drum placed into the front bearing surface when reinstalling the front panel. One word of caution, My wife tried to remove the felt bearing on the bottom of the front panel thinking that it was lint.

I found that the inside of my ten year old dryer was unbelievably full of lint. I'm sure that the efficiency improvements by cleaning the air passages will be substantial and I've just saved $400 on the price of a similar dryer ($900 if my wife and I decided to upgrade to the "new" model that we wanted but really didn't need.

Handyman installed the finally correct switch. It was not the starter button.
This company was wonderful. Replaced each part without charge and rushed the replacements to us. Can' say enough good things to thank them for their courtesy.