GIDP100JD3WW General Electric Dryer - Instructions

It just slipped on. But, the ease in ordering this part was amazing. I am not mechanically inclined at all. I use repair people for mostly everytning, but, $50 to just look at it was too much!! Then I decided to look online and it was the right choice. I will use and/or suggest PartSelect ;-)

I pulled the old handle off and pushed the new one on.
No problem at all.

It's no surprise that GE would use cheaply made parts in such a mass produced product, but it was irritating to see the start switch fail just fourteen months after purchasing the dryer. I am glad that a little thought was put into an easy snap and twist installation of the control panel switches. The original switch failed, due to arcing and pitting of the contact points no doubt, and the local parts house didn't even recognize the part, let alone have it in stock. Thanks to PartSelect.com I could have the part in just a couple of days!
The panel comes appart with just four star driver screws on top, but an allen wrench will work also. Wire jumpers with spade connectors are pulled apart and reattached with needle nose pliers.
In the mean time to keep the dryer operational, I did some creative "re-assigning" of some of the control panel jumper wires using the switch that controled the "Wrinkle Care" setting as a temporary Start Switch as it had the same current handling limits. By the way before attempting such a temporary bypass setup, consider not voiding any warrantee arrangement still applying to the product and have some basic electronics and safety knowledge, study the provided schematic well attached to the back panel and remember to write down all of the original wire connections. And when in doubt, calling a qualified GE appliance repair person is your best and safest bet.
New part went right in in about 15 minutes with original wiring restored and double-checked and the dryer is running right on que again.
Thanks PartSelect.com!

just replaced the unit handle and how my wife can open the dryer without a screwdriver

The part came today…and I installed it in 10 minutes. The only time consuming part was locating a torx screwdriver which was needed to remove the panel.
Lifted the panel, extracted the existing switch and
disconnected the wires and used a flathhead screwdriver to lift off the existing switch. Reconnected the new piece, and voila my dryer worked!
Your site is great!

Remove top control panel, disconnected wire from old switch to new switch (remover 1 wire at time so it would not get mixed up)twisted old switch out inserted new switch and replaced control panel now works like it should. I thought it might would be a safety issue is why I replaced it

My daughter, who has the dryer in Florida, made the repair herself. She removed the broken handle that had been temporarily taped in place. Cleaned off tape residue with Goo-Gone. Then took the new handle and snapped it into place. Worked just like it was supposed to.

Take out the two screws holding the top on with the door open remove top and remove two small screws in top front corners. I replaced the 4 slides and the drum bearing without the new felt, do not do this it continued to squeek after it ran the first few times when i got the new felt a week later i installed it in ten minuites and the noise is gone. I think it cost around sixty dollars and my dryer is back in action. Make sure that you clean all of the lint out of the inside of your dryer I had alot of build up near the chute for the lint trap.

Turned off breaker, rmoved back panel, removed timer, replaced knob. Put back together.

Unplugged dryer. Removed four back panel screws to expose the switches. Removed the wires from the bad switch and transferred them to the new switch. Lifted locking tab on switch and rotated it so the two locking tabs aligned with the slots. Removed old switch and inserted new switch. Rotated about a half turn and replaced the four panel screws. Plugged in the dryer and tested. Very easy repair.

if your unit has over 6,000 hours of operations, one needs to remove the front panel and inspect the sliders that the drum rides on. The video were very helpful to replace the sliders. Unfortunately, my dryer had over 10,000 hours of operations over a 30 years period, hence a major repair costing over $200.00 dollars. The drum sliders were gone, hence the drum eat through the plastic guides. More so, the drum started to eat away the front panel. If the dryer is eating your closes and making a noise, one is looking at a $200.00 repair job. Hence check the sliders early will save one $$$$.

remove 3 screws from back of top panel unplug wires from back of switch and twist out switch and replace same reassemble panel and plug it back in

Hand replace

Open the door and removed the part. Installed the new part and started the dryer.

Searched the sites order # online, called, ordered, delivered PDQ, unpackaged, popped in. That was it.