GFDS355EL1MS General Electric Dryer - Instructions

I took off the dryer top and saw it was the slides went on line found PartsSelect, found my dryer, ordered the parts and had them within two days and it took me about 15 minutes to fix the dryer which will add about 3-4 years more life on it. Thank You PartsSelect My wife is even happier

First I removed the 2 screws that hold the lid down. Then I pulled the lid off. Then I removed the 2 screws that hold the front of the dryer in place. Then I lifted the drum a little and pulled the front cabinet out a little so I could see the drum slides. I removed the bad drum slides and installed the new ones. I then put everything back together and turned on the dryer. The squeeky noise was gone.

I took out a whooping four (4) screws, two that held down the top to the front panel then two screws that attached the side panels (at the top) to the front panel, raised the drum from the inside, leaned the front panel foreword, popped out the old slide (there was only one left), installed the four new slides & put it back together. That's pretty much all there was to it, vary simple.

it was easy, it clip right on.needed to give it a little tap to get it in .

All the stores had either a smaller watt or a larger watt and the book suggested always using the correct watt. I was glad to find it on this sight and it was delivered very quickly.

I followed the directions from the previous post. It was much easier than described. I got the part, removed 4 screws, removed the top, pulled the front and replaced the part. It was all together again in 15 minutes. Dryer sounds great again! I'm so glad I didn't call a repair man!

Unscrewed screws took off new parts and replaced with new parts and put back together. Works great now! No Noise!

We removed the top of the the dryer and then removed the front part. Then put the traps in place, put the other parts of the dryer back on, and turned the dryer back on. Just as simple as that. No extra fees.

snap in snap out

Removed top cover by removing 2 screws in front door opening. Then removed front door removing 2 screws, one on each inner side of the front door.
Removed 2 screws on side doors located about 9 inches from bottom of dryer to permit taking off drum. Slip off belt and remove drum.
Thinking I had a bad bearing, I decided to turn the dryer on and found out I had a bad motor-still functional but noisy. I had difficulty installing the new belt since there was not access panel (which was mentioned in the service manual), so I decided to take off the left side panel-about 8 screws. With the left side panel off, it was a lot easier to install a new belt and install the new front bearings. I actually did not fix the noise, since I need to replace the motor ($$$). When it goes really bad, I can order it then, and it should not take me long to replace it.

Took off the top and front of the dryer---really easy, just two screws for each. Put new drum slides (4) on the front/sides of the drum. Then things got a little bit more difficult. Removed the drum entirely, vaccuumed everything out and had to replace the rear bearings. My husband did this part so I can't tell you exactly how he did it. Not too difficult though. The written directions from here were hard to read---need to make a new copy from the original as it's so copied that it's all smudged. Anyway, once we got the new bearings on, we put everything back together. Dryer works like a charm, at a fraction of the cost it would have been to get someone out to do it. Thanks a bunch for the fast service!

Removed the 3 star screws, putting in a piece if wire as I removed them. Wire was not stiff enough and let the drum slip thus binding making it hard to remove. Started over. Finally called a friend for help. I bought 3 tension pins the same size as the screws. When removing the diffuser screws, insert a tension pin in the hole as you remove each of the screws. The tension pins are hard metal and do not have a head. The diffuser will slip over them. After the diffuser was in place, we turned on the dryer to make sure it was running ok. I noticed what looked like lint toward the front. It was part of the felt gasket on the front of the drum and front of the dryer. We removed the screws on the dryer front and pulled it forward. The felt was rethreaded into its slot, put the front back in place,and replaced the screws that hold everything in place. If you turn the part of the dryer that spins by hand, make sure you are turning it in the correct direction. Turning it the wrong way is probably what caused the felt gasket to come loose causing more work.

I ordered and replaced the front and rear bearings, including the slides that go on the front bearing. Most of this was un-necessary; replacing the slides would have been sufficient, and much easier to do. Two of the old slides were worn completely away.

no problem open top remove front install new belt

Removed the top of the dryer 2 screws. procedure
open dryer door. At the top of the dryer door their is
two screws left to right, Remove them and lift top
off. Inside where the top was is two screws left to
right. Remove the two screws and take the front
panel off. Carefull not to pull wireing loose. Lean door against something so you don't have to disasemble wireing. Pull broken belt out and install new belt around tumbler and up and over
tension pulley and pull down and slip over the motor pulley. Your'e done. Reassemble front then
top. My dryer ran just fine after these steps. The question and answers helped me do this.