GFDN245GL1BB General Electric Dryer - Instructions

Un plug the dryer. Gather phillip, flat head and torix screw drivers. Remove the rear of the dryer to get the spec sheet with the appropriate part number. Next called for part. Belt installation requires removal of front and top of dryer in order to slide belt over the drum. Getting to all the fastners requires tilting the dryer on its back. Clean out excess lint from dryer interior and duct work. Slide drive belt over drum and use some masking tape to hold it in position. Reassemble dyer. Return dryer to upright position and put the belt on the pully and tensioner from rear access port. Remove tape. Replace access panel. Reattach vent duct work. Plug in. There are 5-6 different size screws holding everything together...you may want to use masking tape to label where each type of screw goes. All totaled it took about an hour and cost less that $25. Well worth the effort.

Removed 2 screws to remove top. Removed 2 other screws to remove front. Removed old parts. Installed new parts. Reassemble all afetr cleaning duct work out.

Well, the intall would have been great except for the fact that I needed another part. If your belt breaks there is a reason for it. Make sure you check all the parts that work with the belt. Their was a pully the was defective and also need to be replaces. I think it would be a good idea to put a little note on the page for the Belt Drive to let people know that if you are replaceing the belt you might want to check the Idler Pully for it too might need to be replaces. I'm not an expert and if that was on the page for the Belt Drive I might have look at the pully before I ordered and I would have ordered the part along with the Belt Drive. As it was had to wait another 4 day to get my dryer fixed. I'm very happy the Parts Select has all my parts and they pretty good at getting them out to me in a good amount of time when I need them.

Pulled the drum an found spade clip burned on wire. Hi limit Thermostat crumbled/ broke while pulling spade clip so I trimmed back the wire, cleaned the spade clip and soldered the wire back on. Isolated the other thermostats in the system and tested for resistance. Reassembled dryer.

Unplug the dryer. Remove top panel (remove two screws on the upper inside edge of the dryer door). Lift the front panel from front (tabs and slots at the back) and lift off. Remove the front panel (remove a screw from each side - top/front). Front panel sits on two feet at the bottom, tilt it forward from the top and lift it up (careful not to damage the electrical connection at the bottom left side). I found the dryer had another damaged part (plastic guide that the Slide WH and the Drum Slides connected to was badly worn). After ordering the additional part I attached the slides (white and gray) to the guide. Set the front panel back on the two feet and tilt it back into place (you'll need to slightly raise the drum back into position - easy). Replace the two screws that connect the front panel. Replace the top cover. The whole repair took less than 1/2 an hour including the time it took to vacuum out the dust. Total cost, about $35!

loosened two hose clamps and four screws to replace the anti siphon valve.

The gentleman knew what the problem was, sent the right part, and I looked like I was smart.

Piece of cake, mostly because of the nice exploded drawing that was on the site when ordering the parts, it was easy to identify what was needed and order it.

I will never call a repair man again :-)

Screwed the light bulb into the socket (duh)

Took off control panel,top,leftside facing door,and,door panel. Replace the 2 green and 2 white slides, the front drum bearing, the rear bearing and groundind strap behind the heating element,and new belt. Put back together,run's and sounds like new. The hardest part was putting drum bearing in inside and backside of drum by yourself. Replace belt with left side panel off. Easy to get on that way.

Removed top cover by removing 2 screws in front door opening. Then removed front door removing 2 screws, one on each inner side of the front door.
Removed 2 screws on side doors located about 9 inches from bottom of dryer to permit taking off drum. Slip off belt and remove drum.
Thinking I had a bad bearing, I decided to turn the dryer on and found out I had a bad motor-still functional but noisy. I had difficulty installing the new belt since there was not access panel (which was mentioned in the service manual), so I decided to take off the left side panel-about 8 screws. With the left side panel off, it was a lot easier to install a new belt and install the new front bearings. I actually did not fix the noise, since I need to replace the motor ($$$). When it goes really bad, I can order it then, and it should not take me long to replace it.

I ordered and replaced the front and rear bearings, including the slides that go on the front bearing. Most of this was un-necessary; replacing the slides would have been sufficient, and much easier to do. Two of the old slides were worn completely away.

First I removed the 2 screws that hold the lid down. Then I pulled the lid off. Then I removed the 2 screws that hold the front of the dryer in place. Then I lifted the drum a little and pulled the front cabinet out a little so I could see the drum slides. I removed the bad drum slides and installed the new ones. I then put everything back together and turned on the dryer. The squeeky noise was gone.

I took out a whooping four (4) screws, two that held down the top to the front panel then two screws that attached the side panels (at the top) to the front panel, raised the drum from the inside, leaned the front panel foreword, popped out the old slide (there was only one left), installed the four new slides & put it back together. That's pretty much all there was to it, vary simple.

Unscrewed screws took off new parts and replaced with new parts and put back together. Works great now! No Noise!