GFDN245EL1MG General Electric Dryer - Instructions

This is a space saver one piece unit with dryer on top. I first removed ten screws that hold the top on, I then removed four more screws that hold the front service cover on and two last screws that hold the rear service cover on. Now I seperated the front cover of the dryer from the dryer tumbler tub and slipped the new belt around the tub, then at the rear service cover I feed the belt through the tensioner and back onto the motor pully. Now just put the covers back in reverse order of removal and all done! "Piece of cake"
Ron

Removing the top and then the front of the dryer went fairly easily after finding the screws. The drum came out with just a little coaxing, does not gets screwed in place. To me the trickiest maneuver was getting my hand under the drum to place the belt over motor pulley and around the tensioner pulley. You must look up an image of the belt routing. It took me forever to figure that out. If not for that, this in a half hr fix. Ps don't forget to unplug the dryer.

Followed the Part Select video instructions which made the repair really easy!! Thanks for a job well done! ALSO.. the drum wobble was not caused by worn slides and felt. There are three screws holding the drum axle flange. Two of them fell out leaving the drum to flop about as it rotated. So we scavenged some screws from elsewhere on the dryer and problem solved. Once again.. thanks to Part Select for great instructional videos and great customer service ordering parts.

Before removing the old part,took photo with my phone camera to document the color wires hook up. Screwed in the new part and hooked up the color coded wires using the photo as reference. I was surprised how easy it was. Thanks. Partselect gave me fast shipping, cheap price and great customer service.

I followed the provided video precisely. Made the job quite easy. My only problem is I'm 6'2", 275 lbs. with bad knees. Can't go at it exactly as shown in the video because I can't squat down in front of the dryer without pain. Called in a neighbor of smaller stature for him to come from one side, and me from the other. Worked flawlessly. Video is excellent. I do recommend wearing gloves and/or long sleeve shirt. I cut up my arms a bit, but that could have been easily avoided.

Followed the video which made it real easy.

Watch the video on how to replace the belt on PartSelct site belt installation page.

Easier than I thought it would be. I was hoping it was the front bearing because replacing the rear bearing looked pretty gnarly. Unplugged the dryer from the outlet. Removed two screws inside the door frame. Lifted the top off. Unscrewed the two screws holding the front on. Lifted the front panel off, careful of the wires going to the door. Popped out the old front bearing by releasing the two clips at the top. The old bearing was pretty trashed. The two grey/green slides were in tatters and one of the white ones was missing. Not too much lint inside the dryer, but the lint trap was pretty clogged. Cleaned the insides out with the shop-vac. Inserted the new slides into the new bearing an snapped it back into place, careful to make sure the light went in the hole. The felt gasket at the botton was in good shape so did not replace it. Replaced the panels screwed them back to together and it fired up smooth and quiet.

This is the 2nd time we had to replace the slides. Not a big deal. Removed the top & front of the dyer and replaced the new slides. It's also a good time to vacuum out the inside while you have it apart. Be advised.... Get your tools ready. You'll be receiving your parts quickly. Couldn't believe how fast they arrived!

Thanks to your great DYI video I completed the repair in less than 45 minutes very easy.

Great service. I got the part in 3 days and having the youtube video was fantastic. I also was able to find other videos also so doing these tasks yourself nowadays is much easier. I was a bit nervous but it turned out to be easy.

The clothes would get caught where the drum slide should be (it was almost totally worn down) and would leave black marks. I watched Parts Select youtube video. Bought the parts needed from Parts Select. They arrived within a couple of days. I replaced the 2 drum slides and no more getting caught. Took about 20 minutes.

Replaced drum bearing part and white slides.The problem was that it was not the drum slide support. It appears to be the the drum rear bearing of whch I am now ordering. The bearing replacement is a little more difficult, but I have taken this on as a challenge

Dryer would turn on when you pushed the "on" button, but as soon as you let go, it would turn off. Found the plastic door switch cracked (from slamming door closed). Unplugged the dryer. Unscrewed the two screws inside the top of the door to unfasten the top panel. Took the top panel off. Then unscrewed the two screws on the side to unlatch the front panel. Used plyers to take the 3 wires off the switch and slid the switch through the front of the door. Juat remember where the wires go. Then inserted new switch and connected the wires. Vacuumed out the dryer and reassembled. It took about 20 minutes and was easy! If I can do it, you can!!!

Unscrew the top panel parts three screws. Then another three or six screws to get to the dryer front which needs only to lift straight up about two inches. Pull back slightly and replace the teflon slides. To replace the slides they lay on a tiny plastic pin and slightly bend into the slot to hold them in place. Reseat the dryer drum. Reverse the process to make it like new. From the time you start hearing the dryer squeak, BE CERTAIN to replace these within a week or two (depending on usage.)Otherwise, you may wear out the housing where the teflon would rest. If that happens, you will be out more money to replace the housing and a lot more time to install. Been there and done that. Trust me.