GFDN245EL1BB General Electric Dryer - Instructions

r/r parts unit runs great

i first popped off the top of te dryer after removing the two screws in frotn when you open the door. I then removed the two screws holding the front together. after tilting the front out i was able to place the slides in without having to pull of the front entirely.

removed two phillips screws from front panel, removed front panel and raised top cover, had my wife hold up top cover while i removed belt and installed new one, reassembled in reverse order, turned on dryer and checked for proper operation, and yes i did unplug the unit. worked great!!

I followed the great tips from the other repairs and that part was easy. Turned out not to be the exact problem. The problem was the rear bearing shaft which in another 20 min I had the drum out and repaired. Now the dryer is like new and will hopefully last another 5 yrs.
Thanks Parts Select for your help!

Took the top of the dryer off by removing two philips screws in front. Removed two screws holding the front of the dryer on. Pulled the front out enough to reveal the worn drum slides. Replaced them. Reassembled.

We removed the top of the the dryer and then removed the front part. Then put the traps in place, put the other parts of the dryer back on, and turned the dryer back on. Just as simple as that. No extra fees.

snap in snap out

Initially purchased just the plastic slides, but when I opened the dryer I found the top drum bearing was smashed and the plastic was basically gone in a whole section, so I then ended up ordering the bearing as well. If you hear the loud squeaking, just buy the top drum bearing and the 4 slides (two white and two dark green). It is an easy repair and the squeaking sound is gone.

Just like the other stories, remove the top and front of the dryer, replace the bearing and slides (or slides only if needed). I ordered only the slides, but also needed the bearing because I didn't realize the drum had worn through the bearing already.

pulled off the top, pulled off the front then replaced the plastic that was supporting the front side of the drum. fairly easy to replace although the little plastic 'slides' (you need 4 of them)

Took off the top and front of the dryer---really easy, just two screws for each. Put new drum slides (4) on the front/sides of the drum. Then things got a little bit more difficult. Removed the drum entirely, vaccuumed everything out and had to replace the rear bearings. My husband did this part so I can't tell you exactly how he did it. Not too difficult though. The written directions from here were hard to read---need to make a new copy from the original as it's so copied that it's all smudged. Anyway, once we got the new bearings on, we put everything back together. Dryer works like a charm, at a fraction of the cost it would have been to get someone out to do it. Thanks a bunch for the fast service!

Removed the 3 star screws, putting in a piece if wire as I removed them. Wire was not stiff enough and let the drum slip thus binding making it hard to remove. Started over. Finally called a friend for help. I bought 3 tension pins the same size as the screws. When removing the diffuser screws, insert a tension pin in the hole as you remove each of the screws. The tension pins are hard metal and do not have a head. The diffuser will slip over them. After the diffuser was in place, we turned on the dryer to make sure it was running ok. I noticed what looked like lint toward the front. It was part of the felt gasket on the front of the drum and front of the dryer. We removed the screws on the dryer front and pulled it forward. The felt was rethreaded into its slot, put the front back in place,and replaced the screws that hold everything in place. If you turn the part of the dryer that spins by hand, make sure you are turning it in the correct direction. Turning it the wrong way is probably what caused the felt gasket to come loose causing more work.

As I pulled each of the 3 bolts, I put a alignment rod into each of the holes. After I pulled the old deflector off, I had basically 3 pins/rods to slip the new deflector on and keep everything in basic alignment. Pulled one rod, reinstalled the bolt, so on and so on. Ran motor for noises or misalignment and had neither. Pretty simple repair.

no problem open top remove front install new belt

Removed the top of the dryer 2 screws. procedure
open dryer door. At the top of the dryer door their is
two screws left to right, Remove them and lift top
off. Inside where the top was is two screws left to
right. Remove the two screws and take the front
panel off. Carefull not to pull wireing loose. Lean door against something so you don't have to disasemble wireing. Pull broken belt out and install new belt around tumbler and up and over
tension pulley and pull down and slip over the motor pulley. Your'e done. Reassemble front then
top. My dryer ran just fine after these steps. The question and answers helped me do this.