DSKS333EC2WW General Electric Dryer - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Lynne from Dewitt, IA
- Parts Used:
- WE1X1263
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
dryer knob, plastic broke, could not turn on.
pulled old one off, pushed new one on!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Charlene from Winchester, KY
- Parts Used:
- WE1X1263
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Knob came off
I'm not experience to repair anything so I put the laptop on top of the washer and watch the video and it was easy
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Elbert from LAWTEY, FL
- Parts Used:
- WE25M40
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers
Dryer Squeeky
Watched the video on YouTube and everything went great!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Brian from Richmond, VA
- Parts Used:
- WE4M415
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- More than 2 hours
- Tools:
- Nutdriver, Screw drivers
Dryer would not turn on
It took a while to diagnose the problem. I finally figured out it was the door switch by pushing it with my finger with the dryer door open and starting the dryer. It would run like that, but the switch was not being pressed in enough by the door. I ordered the switch and I should have been able to replace in about 15 min. But the old switch broke while I was removing it and it fell back inside the unit. So I had to remove the top and the front panel to access the door switch. That's why it took so long. If that had not happened it would have been a much simpler repair.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Gene from San Francisco, CA
- Parts Used:
- WE22X35337
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Grid Slide -3 plactic nubs broken slide was loose.
Take old grid slide and pannel off. Clean lint trap wire framework and replace. Make sure this trap frame fits snug against the door, otherwise it puts pressure on the new slide. This is the second time I have replaced this Grid Slide. Slid new pannel into grid frame. Ready to go.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Teddy from Norwalk, CT
- Parts Used:
- WE22X35337
- Difficulty Level:
- Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
The lent filter protector broke
removed broken part and replaced it altogether.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Michell from Bellefontaine, OH
- Parts Used:
- WE25M40
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
Loud Sqeaking noise
the replacement part was easy to replace but remembering how the belt went back on took alittle more time..
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Jeanne from Marblehead, MA
- Parts Used:
- WE1X1263
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
The time knob had broken and come off
Our repair was super easy. All we had to do was line the new Timer Knob up with the knob on the dryer and slip it on. Thank you!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Dee from San Saba, TX
- Parts Used:
- WE1X1263
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
dryer would not turn on
took the old part off @ put the new one on. Took about 5 sec.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Joel from Stockton, CA
- Parts Used:
- WE1X1263
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Broken timer knob
Knob fit perfect. Simple pull off and put new one on.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Fawn from Loganville, GA
- Parts Used:
- WE1M1011
- Difficulty Level:
- Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Dryer door would no longer shut.
Simply popped the old broken part out and popped the new part into place. I wasn't sure if it was the Latch Door or the Door Strike. Once the parts arrived, it was clear the Door Strike was not the issue.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Dave from Redondo Beach, CA
- Parts Used:
- WE1M1011
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
dryer door would not stay closed
inserted the latch into the opening in the front face of the dryer
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Michael from Hopatcong, NJ
- Parts Used:
- WE25M40
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers
Loud screeching noise
I watched video supplied from parts select, only took about 30 minutes, hardest part was putting belt back on, couldn't fit hands in easily, but once I did it, dryer is like new, can't hear a thing.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- David from Oregon, OH
- Parts Used:
- WE25M40
- Difficulty Level:
- Easy
- Total Repair Time:
- 1- 2 hours
- Tools:
- Pliers, Screw drivers
Loud Squeek When Started until warmed-up
Ordered the recommended parts on-line and they showed up the next day. I followed the on-line repair video that described it all step-by-step.
Was this instruction helpful to you?
Thank you for voting!