DMCD330EJ1WC General Electric Dryer - Instructions

TOOK OFF TOP AND FRONT PANEL REACHED IN UNDER TUBE AND REMOVED FROM BELT TENSIONER HARDEST PART IS PUTTING BACK ON TENSIONER TAKES TWO HANDS LAYING ON YOUR BELLY

Watched the video on a different style of dryer so taking apart a bit of a challenge. The old Front Drum Bearing was completely gone on left side and a challenge to pry it off the front dryer panel. replaced felt seal and front drum bearing. noticed that there was 4 places for new bearing slides. the ones i ordered were white and green but did not know why or which one went where as no explanation with packaging. also only ordered one of each and so now had to stop and try and find two more. ! hour later i had brought back a tupperware lid that was thick enough and stated could go to 194 degrees F. i cut out one replacement for green bearing and reused the old white one since it was in good shape from right side of drum bearing. i went back to this website and noticed in the comments section for drum bearing that someone stated the green bearing slides go in at positions 11 and 1 and the white at 10 and 2. they are different materials and having more weight of drum on green now made sense. put machine back together and told neice to keep eyes and ears on dryer thru cycle. she did not even know it was running just in next room.

Exactly how your perfect video instructions showed me. Thank you for a job well done!

Unplugged dryer, slid away from wall, and rotated 90 degrees. I removed top panel, and front panel, pulling off 2 electrical wires, and disconnecting 1 Molex connector, for the door switch. I turned the front panel around, and leaned up against the dryer drum. I removed the light bulb, then snapped off the remains of the upper bearing, then unsnapped the duct panel assembly. I carefully positioned the duct assembly against the front panel, carefully making sure not to pinch any wires, and pressed into place. I then pushed the bottom of the top bearing into the duct assembly, and pushed the top into place, replacing the bearing wear strips, 2 black, 2 white once bearing is snapped into place. I rewired the door switch, put the bulb back in, screwed the front panel, then top panel back on, rotated back into position, plugged it in, and started dryer. Problem solved!

removed top, 2 hex screws, removed front 2 hex screws & 2 star screws. removed belt, slid drum out. Removed old bearing and replaced with new bearing kit. assembled in reverse.
It would help to have another person assist you.

Took apart the dryer housing fairly quickly, pulled out the drum, and installed the kit. Was fairly simple. Then reassembled. The hardest part was trying to get the belt on properly and reconnect to the motor. Believe it or not, I wasted most of my time on the belt. Should've watched the video better and listened to my wife and her suggestions.

When the dryer was installed last year by the dealer, one of the hot leads was not screwed down tightly. Over time the screw loosened and began to arc causing the plastic holding the screw to melt. When I moved the dryer the hot lead fell off and hit the terminal block cover shorting out the dryer. I was able to locate the exact terminal block I needed with their helpful dryer section diagrams. The part came in the time they said. I took off the old terminal block with just 2 attached screws. i kept track of which screws held the hot and neutral conductors and the ground before I removed them. I was then able to slide on the dryer wires and attached the home conductors. I put on the cover plate, turned on the circuit breaker and it worked.

removed rhe control panel, 4 torx screws. removed top of unit 2 philips screws , lifted out of the way ro get to front panel . 2 more torx screws ro get front panel off then juat a matter of changing out worn parts & reassembling dryer unit took maybe an hour thing runs great now

We watched the YouTube video and had it installed in no time. Saved money doing it ourselves.

Replaced dryer motor which was a perfect fit thanks to your help. The process was helped by the internet videos available for the step by step procedure of taking the dryer apart and replacing the bad motor. I also was able to completely clean the inside of the dryer thoroughly, and reassemble it back together .

Called my son-in-law. Easy as pie

Follow the instructions from YOUTUBE to replace the new drive belt..

Dryer was making a horrible noise. When I took it apart I noticed that the from side dryer bearing was ruined. Ordered the part with the slide bars and replaced...Works great...

Our gas GE "Eterna" King Sized capacity dryer started squeaking one day. I was suprised since the dryer was only a few years old, but assumed some grit had invaded and worn a bearing in the belt tensioner. My wife and I have three kids, so we use the dryer daily. The sound got louder quickly and finally it was so loud I had do something. After unplugging the appliance I took the top off the dryer (two screws in the top of the door jam) and the front off (two screws at the top of each corner) and in doing so saw that the drum bearing, which is just a round plastic
"shelf" on which the tumbler drum rides, suspended over the door, was worn through. There were four little "slides" on the bearing surface, and all but one was worn down to dust. I ordered the replacement bearing and slides (two white, I didn't know I also needed two green and have since bought them too) from Part Select and they arrived in about three days. In the meantime I re-assembled the dryer easily and we did use it once or twice, shrieking. When the parts came in I installed them in about 20 minutes, screwing the new bearing onto the rear surface of the front panel, right over the opening for the dryer door. The dryer has worked perfectly since. I used one Phillips head screwdriver for the whole job and paid about $50.00 for the parts. I work in an office and I travel, and when I was a kid I fixed my own cars and stuff, but I'm no appliance repairma! Nevertheless, this was easy! I assume I saved at least $100. The dryer works perfectly and more importantly, it's quiet again!

The first thing I did was move the dryer out so I could "unplug it" !
Then I took the 4 philps head screws out that hold down the top of the dryer, then I lifted up the top and moved it off to the side making sure the wires didn't get pulled out.
Then I removed the 2 5/16 cap screws that holds the front panel on and lifted that off "Make sure you mark the down were the 2 wires for the door swich go" Like white on pin 1 and yellow on pin 2!!!
The next thing is to slide the drum foward so you can remove the element package then remove the 3 philps screws in the back of the drum make sure you have someone hold the element package there is a sheild between the drum and the element package that may fall that is a watch out you will need to move the element package up so you can work on it there will be wires hooked to this ring so becare full you don't break them off.
remove the element package you will see the bearing kit attached to that.
There are 4 5/16 cap screws that hold the bearing kit to that remove them and then remove the old bearing kit you may find and E Ring holding the old bearing kit in place (this would be found in the older models).
Before you install the new bearing kit take the new self tapping screws and tap the holes in the new bearing kit mounting plates this will make things go faster!!!
Now mount the bearing plate with the 4 holes to the element package there is a tab that needs to be mount in there too so look at the old one when you are taking it off.
Pick up the sheild that fell pick it up have a second person help you hold everything in place while you line up the holes for the front plate to the back of the drum and start your screws.
Now tighten them down check to make sure your belt didn't slide off the tensioner that is next to the motor before you slide the drum back in place if it did take the time to figure out how to get it back on the right way our you will be pulling things apart again.
What I did was spin the Drum by hand to make sure everything was ok. you will know if the belt is off it will not move when you spin the drum by hand.
Now that you made sure the belt is on you can put the front back on there are 2 studs on the bottom that you need to set the frount panel on before you can put the screws back in in it.
Now that you have the fron back on it hook your 2 wires back up to the door switch like you took them off!
Now move your top back over and you will see 2 clips on the back of it that slide into a grove in the back now that you have that in place start putting the screws back in put the middle 2 in first and tighten them down them put the last 2 in.
Now plug it back in if your vent pipe fell off hook it back up as you slide your dryer back in place now try it to make sure everything is working right and you will hear the differance.
Good Luck with your repairs....
Just a quick note this dryer is over 40 years old and still going.
I have replace 6 elements and 1 drive belt since it was bought new now the bearing kit.
Clean it once a year and the vent pipe every 6 months it will last!!!