DISR333FCFWW General Electric Dryer - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Rachel from Monsey, NY
- Parts Used:
- WE4M519
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Dryer didn't turn on
The part came today…and I installed it in 10 minutes. The only time consuming part was locating a torx screwdriver which was needed to remove the panel.
Lifted the panel, extracted the existing switch and
disconnected the wires and used a flathhead screwdriver to lift off the existing switch. Reconnected the new piece, and voila my dryer worked!
Your site is great!
Lifted the panel, extracted the existing switch and
disconnected the wires and used a flathhead screwdriver to lift off the existing switch. Reconnected the new piece, and voila my dryer worked!
Your site is great!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- MATTHEW from LIBERTY, SC
- Parts Used:
- WE4M519
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Dryer Would Start Automatic Without Using Start Switch
Remove top control panel, disconnected wire from old switch to new switch (remover 1 wire at time so it would not get mixed up)twisted old switch out inserted new switch and replaced control panel now works like it should. I thought it might would be a safety issue is why I replaced it
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- victor from ST AUGUSTINE, FL
- Parts Used:
- WE18X25100
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
door filter
was no repair- removed filter from door and installed new filter into door. No tools required.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Jay from Niceville, FL
- Parts Used:
- WE01X20419
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Plastic tab broke on handle --- temp taped on.
My daughter, who has the dryer in Florida, made the repair herself. She removed the broken handle that had been temporarily taped in place. Cleaned off tape residue with Goo-Gone. Then took the new handle and snapped it into place. Worked just like it was supposed to.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Michael from Tallahassee, FL
- Parts Used:
- WE4M519
- Difficulty Level:
- Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Pliers
Start Switch Replacement
It's no surprise that GE would use cheaply made parts in such a mass produced product, but it was irritating to see the start switch fail just fourteen months after purchasing the dryer. I am glad that a little thought was put into an easy snap and twist installation of the control panel switches. The original switch failed, due to arcing and pitting of the contact points no doubt, and the local parts house didn't even recognize the part, let alone have it in stock. Thanks to PartSelect.com I could have the part in just a couple of days!
The panel comes appart with just four star driver screws on top, but an allen wrench will work also. Wire jumpers with spade connectors are pulled apart and reattached with needle nose pliers.
In the mean time to keep the dryer operational, I did some creative "re-assigning" of some of the control panel jumper wires using the switch that controled the "Wrinkle Care" setting as a temporary Start Switch as it had the same current handling limits. By the way before attempting such a temporary bypass setup, consider not voiding any warrantee arrangement still applying to the product and have some basic electronics and safety knowledge, study the provided schematic well attached to the back panel and remember to write down all of the original wire connections. And when in doubt, calling a qualified GE appliance repair person is your best and safest bet.
New part went right in in about 15 minutes with original wiring restored and double-checked and the dryer is running right on que again.
Thanks PartSelect.com!
The panel comes appart with just four star driver screws on top, but an allen wrench will work also. Wire jumpers with spade connectors are pulled apart and reattached with needle nose pliers.
In the mean time to keep the dryer operational, I did some creative "re-assigning" of some of the control panel jumper wires using the switch that controled the "Wrinkle Care" setting as a temporary Start Switch as it had the same current handling limits. By the way before attempting such a temporary bypass setup, consider not voiding any warrantee arrangement still applying to the product and have some basic electronics and safety knowledge, study the provided schematic well attached to the back panel and remember to write down all of the original wire connections. And when in doubt, calling a qualified GE appliance repair person is your best and safest bet.
New part went right in in about 15 minutes with original wiring restored and double-checked and the dryer is running right on que again.
Thanks PartSelect.com!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Doug from INMAN, SC
- Parts Used:
- WE18X25100
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Old lint filter had deteriorated
Removed old one, inserted new one in slot. Just have to be sure it's turned in the right direction.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- George from ZANESVILLE, OH
- Parts Used:
- WE4M519
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Dryer started as soon as the door was shut
Removed 4 screws at the top of the dryer controls. Pulled the control toward me , pressed the pulled the tab on the switch up, turned the switch counterclockwise, removed the knob and the 4 wires, Plugged the wires to the new switch and reversed the installation
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Barbara from HAWLEY, PA
- Parts Used:
- WE01X20419
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
Door handle broke
Snap off and then snap New one on.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Robert from WOBURN, MA
- Parts Used:
- WE4M519
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
on /off switch would not work
remove 3 screws from back of top panel unplug wires from back of switch and twist out switch and replace same reassemble panel and plug it back in
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Dave from EDGEWATER, FL
- Parts Used:
- WE18X25100
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
take the old dryer lint screen out
Hand replace
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- CHRISTOPHER from PHENIX CITY, AL
- Parts Used:
- WE1X1192
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Pliers
I broke the door strike on the dryer.
Wife was out of town, visiting family. I broke the door strike by wedging the dryer door between the laundry room door, closed the laundry room door and it snapped the door strike breaking it. I ordered the part, and it shipped fast using the standard shipping, nothing fancy. Grabbed a pair of pliers and pushed the new door strike into place. It snapped right in, fits and works perfect like nothing ever happened. The wife will never know :)
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- John C. from Cincinnati, OH
- Parts Used:
- WE01X20419
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
The door handle was comming off had broken hook
I pulled the old handle off and pushed the new one on.
No problem at all.
No problem at all.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- syd from wilmington, NC
- Parts Used:
- WE01X20419
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
no handle
just replaced the unit handle and how my wife can open the dryer without a screwdriver
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Barbara from Sugar Valley, GA
- Parts Used:
- WE25M40
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers, Socket set
dryer had a loud sqeaking noise
removed top, 2 hex screws, removed front 2 hex screws & 2 star screws. removed belt, slid drum out. Removed old bearing and replaced with new bearing kit. assembled in reverse.
It would help to have another person assist you.
It would help to have another person assist you.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Shelly from MURFREESBORO, TN
- Parts Used:
- WE25M40
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 1- 2 hours
- Tools:
- Screw drivers, Socket set
Squeaky dryer
I followed the YouTube video and it gave me step by step instructions however I really needed to replace my dryer slides to fix the problem.
Was this instruction helpful to you?
Thank you for voting!