DDC4500T5WH General Electric Dryer - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Jeffrey from Bismarck, ND
- Parts Used:
- WE09X27634, WE03X37318
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers
High Squeal Noise
The dryer made a loud squeal and I shut it off immediately.
1 - Unplug the dryer
2 - Took the top off and the front off the dryer
3 - Removed the 4 Front Dryer Drum Slides that were worn all the way through
4 - Pulled the bunched up Felt
5 - Vacuumed out the inside of the dryer -Very Important
6 - Put the drum slides in and felt piece
7 - Put the front on top back on
8 - Worked great
1 - Unplug the dryer
2 - Took the top off and the front off the dryer
3 - Removed the 4 Front Dryer Drum Slides that were worn all the way through
4 - Pulled the bunched up Felt
5 - Vacuumed out the inside of the dryer -Very Important
6 - Put the drum slides in and felt piece
7 - Put the front on top back on
8 - Worked great
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Richard from Williston, VT
- Parts Used:
- WE03X37318
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
Dryer squeaks and squeals while running
Took the top of the dryer off by removing two philips screws in front. Removed two screws holding the front of the dryer on. Pulled the front out enough to reveal the worn drum slides. Replaced them. Reassembled.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- michael from Youngstown, FL
- Parts Used:
- WE25M40
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers
making a bad noise in the rear
replaced rear drum bearing kit Still makes the same noise
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Priscilla from San Diego, CA
- Parts Used:
- WE25M40
- Difficulty Level:
- Difficult
- Total Repair Time:
- More than 2 hours
- Tools:
- Pliers, Screw drivers, Socket set
Squeaky dryer
First I removed the drum as described in many other comments. Took me about 10 minutes, pretty easy. Replaced the part which was easy and could be figured out just by seeing how you took the original part off. The hard part was aligning the drum, drum washer, and metal plate back into the drum bearing. I tried over 2 hours to do this and because it rotates and it's almost impossible to line up all the holes, I decided to do it another way.
I took apart the drum bearing from the back panel and then outside of the dryer walls I aligned the drum, washer, metal plate and drum bearing. I screwed them all in together and then, went into the frame and reconnected it at the back w/ the horseshoe looking washer. It worked perfectly and I was frustrated that it took me so long to figure out a different way to do it.
I have to say because of the installation it was a little tough than anticipated but was very happy with the end result (no squeaking) and money savings. Definitely worth giving it a try if you're patient.
I took apart the drum bearing from the back panel and then outside of the dryer walls I aligned the drum, washer, metal plate and drum bearing. I screwed them all in together and then, went into the frame and reconnected it at the back w/ the horseshoe looking washer. It worked perfectly and I was frustrated that it took me so long to figure out a different way to do it.
I have to say because of the installation it was a little tough than anticipated but was very happy with the end result (no squeaking) and money savings. Definitely worth giving it a try if you're patient.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- George from Lynchburg, VA
- Parts Used:
- WE03X37318
- Difficulty Level:
- Easy
- Total Repair Time:
- More than 2 hours
- Tools:
- Nutdriver, Screw drivers, Socket set
Drum squeaked and occassionally would not turn, even though the motor ran.
I ordered and replaced the front and rear bearings, including the slides that go on the front bearing. Most of this was un-necessary; replacing the slides would have been sufficient, and much easier to do. Two of the old slides were worn completely away.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- susan from Cypress, TX
- Parts Used:
- WE25M40
- Difficulty Level:
- Really Easy
- Total Repair Time:
- More than 2 hours
- Tools:
- Nutdriver, Screw drivers, Socket set
It was making a loud noise
First of all, I am a women...I read where it was probably my rear bearings so I ordered the part, it came in just right, then I replaced it put it all back together, and with the computers help, got it going, belt back on and all and then turned it on and walah it still made a loud noise. Shucks, so I read more and it said it could be the front bearings which I should have tried first but didn't read it first. Ordered part and put it on and wallah, that wasn't it. The noise sounded like the paper in a bicycle spoke so I checked the fan. There was the problem. The fan had so much dryer lint behind it it was forcing it against the housing making a noise. Cleaned it removed all the new unnessary parts and re-boxed them and put it back together but just before I put it together the door fell and two wires came loose so I plugged them back in and put the wrong one in the wrong place cause when I plugged the dryer in sparks went everywhere!!!! I need a man now!!! Scared of electricity!! Sure wish I knew if the noise was fixed :).
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Darlene from North Brunswick, NJ
- Parts Used:
- WE01X20419
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Broken Door Handle
I just snapped the door handle on the dryer in less than a minute. I am completely satified. Did I mention I received my part in one day. I ordered online before 3pm and received it the next day before 11am. Very impressed. Thanks PartSelect!!!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- James from Cumming, GA
- Parts Used:
- WE01X20419
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Just cliped it in the holes
I broke the handle
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- MITCHELL from LAFAYETTE, LA
- Parts Used:
- WE01X20419
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
handle broke due to pulling on door
just put new one on. no tools needed fits in holes already there. handle just snaps on,
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Alan from Crest Hill, IL
- Parts Used:
- WE01X20419
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Dryer Door Handle broke
This one is so easy my grandson could do it. The removal was easy, it broke off. The installation was a "snap in place". Thinking I needed a few days of dryer use without the handle, I made a temporary repair. I fished some heavy packing string thru the slots in the door, made a loop, than a knot. This gave my wife something easy to grab to open. Did not even need to do the temporary repair, the part arrived in one day.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- shelly from layton, UT
- Parts Used:
- WE01X20419
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
The plastiic door handle broke off my GE dryer
As soon as the new door handle arrived, I just snapped it into place. It took about two seconds>
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Julie from Sterling Heights, MI
- Parts Used:
- WE03X37318
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
worn dryer drum slides
i first popped off the top of te dryer after removing the two screws in frotn when you open the door. I then removed the two screws holding the front together. after tilting the front out i was able to place the slides in without having to pull of the front entirely.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- DONNA from PLEASANT CITY, OH
- Parts Used:
- WE03X37318
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
loud screaching noise
We removed the top of the the dryer and then removed the front part. Then put the traps in place, put the other parts of the dryer back on, and turned the dryer back on. Just as simple as that. No extra fees.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- David from santa maria, CA
- Parts Used:
- WE03X37318
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
squeaking
snap in snap out
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Robert from Big Rapids, MI
- Parts Used:
- WE03X37318
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
bearing and slides worn out
took off top of dryer, took out 2 screws so front of dryer could be removed, replaced bearing,slides and felt seal
Was this instruction helpful to you?
Thank you for voting!