DDC4400T5WH General Electric Dryer - Instructions

The first thing I did was move the dryer out so I could "unplug it" !
Then I took the 4 philps head screws out that hold down the top of the dryer, then I lifted up the top and moved it off to the side making sure the wires didn't get pulled out.
Then I removed the 2 5/16 cap screws that holds the front panel on and lifted that off "Make sure you mark the down were the 2 wires for the door swich go" Like white on pin 1 and yellow on pin 2!!!
The next thing is to slide the drum foward so you can remove the element package then remove the 3 philps screws in the back of the drum make sure you have someone hold the element package there is a sheild between the drum and the element package that may fall that is a watch out you will need to move the element package up so you can work on it there will be wires hooked to this ring so becare full you don't break them off.
remove the element package you will see the bearing kit attached to that.
There are 4 5/16 cap screws that hold the bearing kit to that remove them and then remove the old bearing kit you may find and E Ring holding the old bearing kit in place (this would be found in the older models).
Before you install the new bearing kit take the new self tapping screws and tap the holes in the new bearing kit mounting plates this will make things go faster!!!
Now mount the bearing plate with the 4 holes to the element package there is a tab that needs to be mount in there too so look at the old one when you are taking it off.
Pick up the sheild that fell pick it up have a second person help you hold everything in place while you line up the holes for the front plate to the back of the drum and start your screws.
Now tighten them down check to make sure your belt didn't slide off the tensioner that is next to the motor before you slide the drum back in place if it did take the time to figure out how to get it back on the right way our you will be pulling things apart again.
What I did was spin the Drum by hand to make sure everything was ok. you will know if the belt is off it will not move when you spin the drum by hand.
Now that you made sure the belt is on you can put the front back on there are 2 studs on the bottom that you need to set the frount panel on before you can put the screws back in in it.
Now that you have the fron back on it hook your 2 wires back up to the door switch like you took them off!
Now move your top back over and you will see 2 clips on the back of it that slide into a grove in the back now that you have that in place start putting the screws back in put the middle 2 in first and tighten them down them put the last 2 in.
Now plug it back in if your vent pipe fell off hook it back up as you slide your dryer back in place now try it to make sure everything is working right and you will hear the differance.
Good Luck with your repairs....
Just a quick note this dryer is over 40 years old and still going.
I have replace 6 elements and 1 drive belt since it was bought new now the bearing kit.
Clean it once a year and the vent pipe every 6 months it will last!!!

Took the dryer apart to get to the rear bearing. Took the bearing assembly out, kept the e-ring from the old bearing shaft, replaced the bearing kit, took the o-ring off the new shaft and replaced it with the e-ring, then reassembled the unit. Make sure to place a nail or long screw into into the rear of the drum, so that you can realign bearing on the drum. It is easier with two people when reassembling.

Removed old one, inserted new one in slot. Just have to be sure it's turned in the right direction.

Snap off and then snap New one on.

removed remaining handle pieces and simply snapped the new part in place. very simple,very easy.

Hand replace

All I had to do was remove the damaged filter and replace it with te new one. It could not ave been easier.

just replaced the unit handle and how my wife can open the dryer without a screwdriver

Pulled the drum an found spade clip burned on wire. Hi limit Thermostat crumbled/ broke while pulling spade clip so I trimmed back the wire, cleaned the spade clip and soldered the wire back on. Isolated the other thermostats in the system and tested for resistance. Reassembled dryer.

Used online instructions. Worked well.

Removed 2 screws to remove top. Removed 2 other screws to remove front. Removed old parts. Installed new parts. Reassemble all afetr cleaning duct work out.

Had a repair shop quote 230 for repair . Spent 66 on parts and did the repair in 45 minutes using the instructions from folks on this site . Very happy with results thanks

- Removed two screws at top left and right of door.
- Removed top dryer panel
- Removed two screws holding front panel in place
- Noticed drum slide was missing because front drum bearing was worn away and slide had fallen off.
- Went ahead and removed drum to replace rear drum bearing (probably not needed; should have disassembled it first to discover this). Would have been better to pull drum first (loosen idler pulley and release belt, pull drum straight out) instead of attempting to unscrew bearing. Be sure to note how the idler pulley is set.
- vacuumed tons of lint up
- Replaced bearing (needed a second person for this; drum too big to reach around. be sure to pre-thread the bearing)
- Ordered front drum bearing, waiting to repair it now, should be good after this.

My husband and I had taken apart this dryer before, so the second time was a lot easier. The first time we took it apart it took 2-3 frustrating hours. So, if it's your first time, plan for longer.

1. Before we started anything we unplugged the dryer and disconnected the vent.
2. We removed the top and loosened the contol panel on top.
3. We removed the front. Be careful of the wires. You can label them, or just remember where they go.
4. Lay the dryer down on it's back. This make's it easier to remove the drum.
5. Remove the drum, but gently slide the belt off first. Don't stretch the belt removing it.
6. Once the drum was removed, we removed the screws from the inside of the drum.
7. We didn't need to use the entire kit, just the part that sits in the center and spins...kinda looks like a top. (Yes, that's my technical description)
8. We screwed in the new "top" and put the dryer back together.

Really the only part I had to help with (this time)was putting the drum back in to make sure it sat where it was supposed to. It made a big difference that it was laying on it's back...we didn't do that the first time, which was part of our frustration.

Putting the belt back on is a little tricky too. We had instructions still for our dryer to refer to put it back on. If you don't have yours, just google or bing for the instructions. There's website's out there with great pictures.

After removing pieces that were stuck in the door, I simply popped the new handle in place. It took less than a minute. What was the easiest was ordering and receiving the new parts- I ordered and 2 days later I received the new parts. I didn't expect to get the new parts for at least a week.