DDC4400T4WH General Electric Dryer - Instructions

My husband and I had taken apart this dryer before, so the second time was a lot easier. The first time we took it apart it took 2-3 frustrating hours. So, if it's your first time, plan for longer.

1. Before we started anything we unplugged the dryer and disconnected the vent.
2. We removed the top and loosened the contol panel on top.
3. We removed the front. Be careful of the wires. You can label them, or just remember where they go.
4. Lay the dryer down on it's back. This make's it easier to remove the drum.
5. Remove the drum, but gently slide the belt off first. Don't stretch the belt removing it.
6. Once the drum was removed, we removed the screws from the inside of the drum.
7. We didn't need to use the entire kit, just the part that sits in the center and spins...kinda looks like a top. (Yes, that's my technical description)
8. We screwed in the new "top" and put the dryer back together.

Really the only part I had to help with (this time)was putting the drum back in to make sure it sat where it was supposed to. It made a big difference that it was laying on it's back...we didn't do that the first time, which was part of our frustration.

Putting the belt back on is a little tricky too. We had instructions still for our dryer to refer to put it back on. If you don't have yours, just google or bing for the instructions. There's website's out there with great pictures.

Pulled the drum an found spade clip burned on wire. Hi limit Thermostat crumbled/ broke while pulling spade clip so I trimmed back the wire, cleaned the spade clip and soldered the wire back on. Isolated the other thermostats in the system and tested for resistance. Reassembled dryer.

It went perfect , just put it in. No tools needed.

I ordered the part via the internet. The shipping date was delayed twice but you excellent customer service department followed through and expedited the order. I installed it myself. Thank you.

Watched a video online on how to replace the belt, it pretty much told me what to look for to get the drum out. Followed the instructions sent with the bearing kit and removed the old bearing assembly. Ran the screws supplied with the kit into the bearing assembly before I installed it. This was a tip I got off PartsSelect website. Running the screws in first is a must! Had my wife hold the assembly in place while I ran the screws in. That part of the job is the only time you need an extra set of hands. Put the dryer back together and it works like a quiet champ now.

Snapped on new handel. Took all of 5 seconds. The hardest part was finding the part, which your website took care of....Thanks!

Very satisfied. I simply took the plastic door handle out of the package and snapped it into the door. It popped right in and fit perfectly!

Just popped the new door handle on.

Simply pulled off the old handle and snapped in the new one! No tools required. Took about 5 seconds!

This one is so easy my grandson could do it. The removal was easy, it broke off. The installation was a "snap in place". Thinking I needed a few days of dryer use without the handle, I made a temporary repair. I fished some heavy packing string thru the slots in the door, made a loop, than a knot. This gave my wife something easy to grab to open. Did not even need to do the temporary repair, the part arrived in one day.

As soon as the new door handle arrived, I just snapped it into place. It took about two seconds>

I ordered and replaced the front and rear bearings, including the slides that go on the front bearing. Most of this was un-necessary; replacing the slides would have been sufficient, and much easier to do. Two of the old slides were worn completely away.

It was so easy, I just depressed a couple of tabs and it popped right in!

I broke the handle

I ordered the new part as listed and it came in two days, which was amazing to me since it was the week before Christmas. I snapped it in in less than a minute and all is well. Thank you for being so prompt on sending this out. Made the holidays a lot easier.