DCCB330GJ1WC General Electric Dryer - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Barbara from Sugar Valley, GA
- Parts Used:
- WE25M40
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers, Socket set
dryer had a loud sqeaking noise
removed top, 2 hex screws, removed front 2 hex screws & 2 star screws. removed belt, slid drum out. Removed old bearing and replaced with new bearing kit. assembled in reverse.
It would help to have another person assist you.
It would help to have another person assist you.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Cheryl from WILDER, KY
- Parts Used:
- WE01X20419
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
Door handle broke
Called my son-in-law. Easy as pie
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- George from Dassel, MN
- Parts Used:
- WE25M40
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 1- 2 hours
- Tools:
- Pliers, Screw drivers, Socket set, Wrench set
Dryer squeaked when running
Took the dryer apart to get to the rear bearing. Took the bearing assembly out, kept the e-ring from the old bearing shaft, replaced the bearing kit, took the o-ring off the new shaft and replaced it with the e-ring, then reassembled the unit. Make sure to place a nail or long screw into into the rear of the drum, so that you can realign bearing on the drum. It is easier with two people when reassembling.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Joseph from Freeland, MI
- Parts Used:
- WE25M40
- Difficulty Level:
- Easy
- Total Repair Time:
- 1- 2 hours
- Tools:
- Screw drivers, Socket set
loud noise when ran for 5 min.
Replaced the rear drum bearing. Not doing it before ,it took about 1 1/2 hrs. Problem was fixed.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Jay from Niceville, FL
- Parts Used:
- WE01X20419
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Plastic tab broke on handle --- temp taped on.
My daughter, who has the dryer in Florida, made the repair herself. She removed the broken handle that had been temporarily taped in place. Cleaned off tape residue with Goo-Gone. Then took the new handle and snapped it into place. Worked just like it was supposed to.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Barbara from HAWLEY, PA
- Parts Used:
- WE01X20419
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
Door handle broke
Snap off and then snap New one on.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Danny from DOVER, AR
- Parts Used:
- WE01X20419
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
broken dryer door handle
removed remaining handle pieces and simply snapped the new part in place. very simple,very easy.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Doug from INMAN, SC
- Parts Used:
- WE18X25100
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Old lint filter had deteriorated
Removed old one, inserted new one in slot. Just have to be sure it's turned in the right direction.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- syd from wilmington, NC
- Parts Used:
- WE01X20419
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
no handle
just replaced the unit handle and how my wife can open the dryer without a screwdriver
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Phuc from WOODBRIDGE, VA
- Parts Used:
- WE03X29897
- Difficulty Level:
- Easy
- Total Repair Time:
- 1- 2 hours
- Tools:
- Screw drivers
drive belt is broken.
Follow the instructions from YOUTUBE to replace the new drive belt..
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Darryl from FARR WEST, UT
- Parts Used:
- WE17X22217
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 1- 2 hours
- Tools:
- Pliers, Screw drivers, Socket set, Wrench (Adjustable)
Bad dryer motor
Replaced dryer motor which was a perfect fit thanks to your help. The process was helped by the internet videos available for the step by step procedure of taking the dryer apart and replacing the bad motor. I also was able to completely clean the inside of the dryer thoroughly, and reassemble it back together .
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Shelly from MURFREESBORO, TN
- Parts Used:
- WE25M40
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 1- 2 hours
- Tools:
- Screw drivers, Socket set
Squeaky dryer
I followed the YouTube video and it gave me step by step instructions however I really needed to replace my dryer slides to fix the problem.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Michael from Laurel Springs, NJ
- Parts Used:
- WE03X29897
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 1- 2 hours
- Tools:
- Screw drivers
dryer belt snapped
Replaced it as one would. I took off the front facing and replaced the belt. It took a bit of searching to find the proper way to route the belt around the pulley.
It took a while since it was my first time and I wasn't sure what to take apart and what to leave intact.
If I were to do it again, it would take 30 minutes or less.
It took a while since it was my first time and I wasn't sure what to take apart and what to leave intact.
If I were to do it again, it would take 30 minutes or less.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- KURT from CEDAR RAPIDS, IA
- Parts Used:
- WE14X25080, WE3M26
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
metal on metal swealing
removed rhe control panel, 4 torx screws. removed top of unit 2 philips screws , lifted out of the way ro get to front panel . 2 more torx screws ro get front panel off then juat a matter of changing out worn parts & reassembling dryer unit took maybe an hour thing runs great now
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Cindy from EPHRATA, PA
- Parts Used:
- WE03X29897
- Difficulty Level:
- Easy
- Total Repair Time:
- 1- 2 hours
- Tools:
- Pliers, Screw drivers, Wrench set
Dryer needed a new dryer belt
I followed the directions I found on my tablet on youtube.
Was this instruction helpful to you?
Thank you for voting!