PFDS455EL0MG General Electric Dryer - Instructions

Faulty Door switch. Dryer would heat up so I knew it wasn't thermostat or element related.

After some research on the internet, I deduced the squeaking sound in our dryer was due to defective drum glides. I ordered a set of four of the white type, knowing only our model requires four glides, but not knowing there are two types for two locations. After disassembling the dryer I realized I needed more parts - two green slides and a new top bearing assembly. The dryer drum had eaten thru glides and into the plastic assembly. That was the reason for the squeaking noise - metal sliding against hard plastic. I ordered the additional parts directly from the manufacturer to ensure I got it right. After all the parts arrived, the repair was easy and took less than 30 minutes. I actually had my 17 year-old daughter do the work to teach her some skills. I just instructed her and stepped in on assembling the top that was just a bit tricky to put back on. Problem fixed.

Dryer would turn on when you pushed the "on" button, but as soon as you let go, it would turn off. Found the plastic door switch cracked (from slamming door closed). Unplugged the dryer. Unscrewed the two screws inside the top of the door to unfasten the top panel. Took the top panel off. Then unscrewed the two screws on the side to unlatch the front panel. Used plyers to take the 3 wires off the switch and slid the switch through the front of the door. Juat remember where the wires go. Then inserted new switch and connected the wires. Vacuumed out the dryer and reassembled. It took about 20 minutes and was easy! If I can do it, you can!!!

Removed top screws. Removed front panel screws. Removed front panel. Replaced worn slides. Removed drum. Replaced drum bearing and retainer. Cleaned lint from dryer, motor and blower assembly. Replaced light bulb. Door latch was purchased as spare. Inspected heating element. Re -assembled. Dryer now running like new again. I expect to have restring a new element in the near future. I like how the GE dryer comes apart. It is best to replace the slides before they wear all the way through.

replaced the parts that had worn out

Unplug dryer, unscrew bulb then replace with a new bulb. Plug dryer back in.

Replaced bulb.

To get to where the drum slides go you have to first remove the dryer top. Then you have to remove the two screws that hold the dryer front/door. Found inside the dryer about an inch down on both sides. Be careful because it will fall off. Lower carefully as there is an electric hook-up on the bottom of the door. On the door top are the brackets that the slides slip into. My dryer has 4 slides. Sold individually for some reason. You are done except for re-assembly. Slip dryer drum back on door, press the front until you hear it click back together. Put screws back in and top back on. You are done and no more screeching!

Removed door strike and latch, replaced, works like new.

The only tool used was a phillips head screwdriver. I removed two screws to lift the lid and two more screws to free the front panel, slid off the front panel, and had direct access to all 4 slides, replaced, reassembled, and good as new.

follow the video, and in no time fix and ran smooth, like brand new, love this website, fast and reliable

Followed the video on this site but did not have to remove wires. Just stand in front and let the front panel rest on your leg while you replace the slides. Quick and Easy!!!!

inserted the latch into the opening in the front face of the dryer

Parts arrived well in time, exactly what was needed. The latch was a snap-in process. The strike require gentile use of a pliers, and went in quickly. Thanks!

I removed the top of the dryer and saw that the top two drum slides where gone and the drum bearing itself was damaged I Temporally placed the parts on the drum bearing until I got the new one, that stopped the squeaking noise. All I needed to do was place the part with the hole on the little hook and then sled the other part in its slot.