GFDN240GL0WW General Electric Dryer - Instructions

Watch the video on how to replace the belt on PartSelct site belt installation page.

I followed the provided video precisely. Made the job quite easy. My only problem is I'm 6'2", 275 lbs. with bad knees. Can't go at it exactly as shown in the video because I can't squat down in front of the dryer without pain. Called in a neighbor of smaller stature for him to come from one side, and me from the other. Worked flawlessly. Video is excellent. I do recommend wearing gloves and/or long sleeve shirt. I cut up my arms a bit, but that could have been easily avoided.

Great service. I got the part in 3 days and having the youtube video was fantastic. I also was able to find other videos also so doing these tasks yourself nowadays is much easier. I was a bit nervous but it turned out to be easy.

Followed the Part Select video instructions which made the repair really easy!! Thanks for a job well done! ALSO.. the drum wobble was not caused by worn slides and felt. There are three screws holding the drum axle flange. Two of them fell out leaving the drum to flop about as it rotated. So we scavenged some screws from elsewhere on the dryer and problem solved. Once again.. thanks to Part Select for great instructional videos and great customer service ordering parts.

followed instructions that came with kit. The problem was the instructions were not very clear with regard to the "type" of burner. the "A" type with the slot is explained but the "B" without the slot wasen't clearly explained. Even that wasen't too bad (I had to re-do that part), But you need to be 20 years old to see the damned print. I had to use my reading glasses AND a magnifying glass to read them. Also with the "B" type burner, which I have, you simply install the limiter part and you don't need (can't) adjust it.

This is the 2nd time we had to replace the slides. Not a big deal. Removed the top & front of the dyer and replaced the new slides. It's also a good time to vacuum out the inside while you have it apart. Be advised.... Get your tools ready. You'll be receiving your parts quickly. Couldn't believe how fast they arrived!

Thanks to your great DYI video I completed the repair in less than 45 minutes very easy.

remove front and top cannover's from dryer.remove plastic inside bearing housing and plastic bearing slides replace worn out bearing slides with new ones. needed 4 bearings direction suggested only two....

Faulty Door switch. Dryer would heat up so I knew it wasn't thermostat or element related.

After some research on the internet, I deduced the squeaking sound in our dryer was due to defective drum glides. I ordered a set of four of the white type, knowing only our model requires four glides, but not knowing there are two types for two locations. After disassembling the dryer I realized I needed more parts - two green slides and a new top bearing assembly. The dryer drum had eaten thru glides and into the plastic assembly. That was the reason for the squeaking noise - metal sliding against hard plastic. I ordered the additional parts directly from the manufacturer to ensure I got it right. After all the parts arrived, the repair was easy and took less than 30 minutes. I actually had my 17 year-old daughter do the work to teach her some skills. I just instructed her and stepped in on assembling the top that was just a bit tricky to put back on. Problem fixed.

very easy

TOO EASY to repair. WORKS GREAT>

Dryer would turn on when you pushed the "on" button, but as soon as you let go, it would turn off. Found the plastic door switch cracked (from slamming door closed). Unplugged the dryer. Unscrewed the two screws inside the top of the door to unfasten the top panel. Took the top panel off. Then unscrewed the two screws on the side to unlatch the front panel. Used plyers to take the 3 wires off the switch and slid the switch through the front of the door. Juat remember where the wires go. Then inserted new switch and connected the wires. Vacuumed out the dryer and reassembled. It took about 20 minutes and was easy! If I can do it, you can!!!

Googled possible problem where noise was coming from. Went to Parts Select web site. Ordered felt and drum bracket. Removed screws behind control knobs and removed top of dryer. Removed two screws on front inside dryer (left/right side) this allowed me to remove front panel of dryer. Unattached wires. Drum bracket is located above door opening...pretty much snaps out, felt piece is located on bottom bracket. Felt piece was replaced and new top bracket replaced. Reattach wires, lift drum slightly to fit doo iInto place. Dryer still made noise. Noticed I did not have any drum slides! Drum slides slide into top of front bracket at 10/2 o'clock position and 11/1o'clock. Easy and very inexpensive dryer repair!! My husband was very impressed that I could take dryer apart and fix!!!

Unscrew the top panel parts three screws. Then another three or six screws to get to the dryer front which needs only to lift straight up about two inches. Pull back slightly and replace the teflon slides. To replace the slides they lay on a tiny plastic pin and slightly bend into the slot to hold them in place. Reseat the dryer drum. Reverse the process to make it like new. From the time you start hearing the dryer squeak, BE CERTAIN to replace these within a week or two (depending on usage.)Otherwise, you may wear out the housing where the teflon would rest. If that happens, you will be out more money to replace the housing and a lot more time to install. Been there and done that. Trust me.