DSLVR48GH1WW General Electric Dryer - Instructions

I watched the repair video 3 times to make sure I was comfortable to do the repair.the video was very helpful.thank you ! Everything went well and the dryer runs great.

I replaced the drum bearing slides and also the main front drum bearing. First, disconnect the electric. Then I removed the two screws inside the door that attach the top cover, removed the top cover, removed two screws that attach the front cover, lift up the front cover and pivot it to the left leaving the wiring attached, removed the front bearing assembly by pulling it out at the top and then up, installed the new front bearing ring and snap it into place, installed the drum bearing slides, reinstalled the front cover, reinstalled the top cover, and tested the drum by turning it by hand first and then under power. The whole operation took less than 15 minutes....

stuck it back in the holes just like the original handle. Had to do a little adjustment because I put screwdriver in them too many times to open the door after the original handle feel off, so the fit was loose. Fixed with tape.

I read the other repair instructions on this site and looked at the parts diagrams. It wasn't entirely clear how everything came apart but once I started by unscrewing the top of the dryer and removing it (screws were just inside the dryer door) it was easy. Unscrewed the front panel next , swung it out, and it was quick work to install the new bearing with the slides. It wasn't too clear in the parts diagrams but I did need two each of the dryer drum slides and front dryer drum slides, four total, two on each side of the drum bearing. The dryer had been running on the old drum bearing itself, the old slides had worn completely down and the bearing itself was starting to disintegrate too. If I'd caught it sooner I could have reused the bearing and just replaced the slides. Saved a lot of $ and the dryer is nice and quiet again!

Unplugged power. removed 2 screws to take of top cover. once inside removed 2 more screws to slide front panel of. I first replaced slides on front panel. I then lift drum and installed new belt. Only trick is to make sure you wrap belt around tension arm pully properly. Basically a very easy job

I order the parts needed to replace the slides, the felt ,and the bearing on a Sunday afternoon. The parts arrived on Tuesday even though I used regular shipping. I followed the instructions posted by another customer. It was extremely easy and only took me about fifteen minutes. My only problem was that I needed 2 each of the front slide and the rear slide, and I unknowingly only ordered 1 of each. I order the other 2 on Tuesday via regular shipping and they arrived on Wed. AMAZING!!!!

this was a part i ordered for future use. i was very happy with the ordering process and speed of delivery from PartSelect.

inserted the lint catcher into the opening to replace the old one

When we first heard the screeching i thought right away that it was the belt. we ordered a new one and after i replaced it the dryer was still just as loud. I wished i went here first. Right away i found others with the same problem, did the same repair which was just taking 2 screws out, sliding the top and front panel off(watch for the electric wire connected to the panel) and replace a couple of plastic slides. now it is better than ever.

had a great video to follow, made it easy to install.

The repair went very well, parts fit perfect. Now there isn't anymore complaints.

I followed the video on how to repair

Key starting point is to remove top cover by removing two long screws located at the front of the cover
Remove control panel and it's bottom and side supports.
Remove short vent pipe by bending retainer tab.
Support the drum at the top using piece of rope.
Remove main rear cover (leave bottom attached).
Remove electric heating unit and install new bearing carrier from kit.
Reinstall the the heating unit
Remove three screws (inside the drum)to release the inner drum cover and release the bearing carrier.
Install new bearing carrier. Note: the three holes in the bearing carrier are not tapped, I suggest that the screws be installed (threads cut) into the bearing cover before attempting to install the bearing carrier.
Install the new bearing carrier. Note: pilot one of the holes using a small nail etc. then go on to install screws in the other two holes remove the pilot device and install the third screw.
Reassemble in reverse order.

I removed the top cover and the back cover to install new belt.
Once i put new belt i discovered that the pulley was also broken so now i have order the pulley so that i can complete the repair

After speaking with your representative and him explaining how to me how simple it would be to switch out this light socket myself. I went on y tube went through the instructions and had to go buy a new dryer. And before you jump to any conclusions I can and do repair and and all of things around my house. I will NEVER purchase anything from you company again ander the pretense that it is so simple. This should have been told to me that an election should have done the job!!!!!! Now not only am I out the money I paid your company but I’m out the money I shelled out for a whole new dryer. I am a very angry customer and I would never recommend you to anyone!!! EVER!!!