DPVH880GJ3MG General Electric Dryer - Instructions

First I got the front bearing, found out I needed the slides too. It was binding at first, so I undid an earlier misadjustment I made (on the back drum mount). and it works!

I was teaching my associate how to do this repair so I showed him how to take off the top of the dryer. Then I showed him how to replace the drum slides. I had him clean out the dryer since we had it apart, and I also showed him how to remove the drum and then reinstall it. This was a very easy repair, and he learned a lot that he otherwise would not have known. Thanks for getting the parts to me so quickly. Rob from Clarks Summit.

Your instructions were execellent
Problem is solve
Thank you

Took off the top and front of the dryer---really easy, just two screws for each. Put new drum slides (4) on the front/sides of the drum. Then things got a little bit more difficult. Removed the drum entirely, vaccuumed everything out and had to replace the rear bearings. My husband did this part so I can't tell you exactly how he did it. Not too difficult though. The written directions from here were hard to read---need to make a new copy from the original as it's so copied that it's all smudged. Anyway, once we got the new bearings on, we put everything back together. Dryer works like a charm, at a fraction of the cost it would have been to get someone out to do it. Thanks a bunch for the fast service!

I ordered and replaced the front and rear bearings, including the slides that go on the front bearing. Most of this was un-necessary; replacing the slides would have been sufficient, and much easier to do. Two of the old slides were worn completely away.

To get inside the dryer in this model is extreemly difficult. I had to remove the side panel. In order to do this I needed to take off the screws on the back cover side where I needed to replace the cord. Then I needed to remove the screws to take off the top cover, front door, rear panel, trim switch, and end cap. I also had to remove the front door. After that I could tak off the side panel and change the cord.

It took a while to diagnose the problem. I finally figured out it was the door switch by pushing it with my finger with the dryer door open and starting the dryer. It would run like that, but the switch was not being pressed in enough by the door. I ordered the switch and I should have been able to replace in about 15 min. But the old switch broke while I was removing it and it fell back inside the unit. So I had to remove the top and the front panel to access the door switch. That's why it took so long. If that had not happened it would have been a much simpler repair.

I followed the varied instructions out there for getting the dryer open. WATCH the videos on uTube; I took out more screws than needed on first attempt -- which isn't a big deal but took me longer than it should have to pull it apart. It appeared the grinding was coming from the dryer bearings due to some abrasion I could see and worn front slides, so I replaced the front slides (4) and the rear bearing. The kids helped by crawling inside the drum to tighten the new bearing bolts (just for fun). When I put it back together it was making a somewhat different grinding noise. It wouldn't make any noise until I put the belt AND front cover on and then it would make a periodic (about every 10 degrees) grind when I rotated the drum; I took it apart and the grinding would stop even if I rotated the blower by hand. Put it together, the grind would start .... It took me awhile to figure out that the blower retaining bolt had come loose so the plastic blower was grinding on the metal cover. CHECK THE BLOWER RETAINING BOLT visible from the front with the dryer door/cover off -- it's not obvious that it's loose by looking at it since the retaining clip still sits over the blower shaft even when it's loose. You might even see small nicks in the blower fan blade. It's super quiet now.

Easier than I thought it would be. I was hoping it was the front bearing because replacing the rear bearing looked pretty gnarly. Unplugged the dryer from the outlet. Removed two screws inside the door frame. Lifted the top off. Unscrewed the two screws holding the front on. Lifted the front panel off, careful of the wires going to the door. Popped out the old front bearing by releasing the two clips at the top. The old bearing was pretty trashed. The two grey/green slides were in tatters and one of the white ones was missing. Not too much lint inside the dryer, but the lint trap was pretty clogged. Cleaned the insides out with the shop-vac. Inserted the new slides into the new bearing an snapped it back into place, careful to make sure the light went in the hole. The felt gasket at the botton was in good shape so did not replace it. Replaced the panels screwed them back to together and it fired up smooth and quiet.

I found a loose connection before I installed the new part. Whats comforting to know about this repair working with Parts Select is that the new part arrived in 1 day, and they excepted my return of the part with no hassle at all.Thanks!

I noticed the original blower wheel was worn, the hole for the motor shaft was reamed out and the blower was not spinning with the motor. Air was not being circulated so the clothes were not drying well. Replacing the wheel was relatively easy. I did see other people commenting on the difficulty of getting the drive belt re installed properly. I noticed a small "lip" bent into the motor frame, and found the arm for the belt tensioner would fit into this lip and it held it out of the way while I reinstalled the drum and reouted the belt onto the motor pulley. Once the belt was in place, I gently let the tensioner out of its holding position and everything went back into place nicely.

Originally ordered heating element kit, but decided to replace drum slides and "o"-ring while the dryer was dis-assembled.Replacing the dryer elements was relatively easy-just follow instructions. Replacing the slides and o-ring was very easy, just clip in place. The dryer vent was almost totally clogged and probably the cause of most problems. This took longer than all mechanical repairs as I have a long dryer vent. I suggest cleaning the dryer vent regularly to avoid problem. I used a 4" circular brush and cordless drill to clean the duct. If you have not cleaned your vent in 2-3 years, you will be amazed at the amount of lint build-up. I was very pleased with the price of parts and customer service at Parts-Select, estimate I saved approximately $250-300.

The clothes would get caught where the drum slide should be (it was almost totally worn down) and would leave black marks. I watched Parts Select youtube video. Bought the parts needed from Parts Select. They arrived within a couple of days. I replaced the 2 drum slides and no more getting caught. Took about 20 minutes.

The repair was extremely easy to do. The video was perfectly done and described everything one needed to do in very simplistic details.

replaced the parts that had worn out