DPVH880EJ3MV General Electric Dryer - Instructions

remove front and top cannover's from dryer.remove plastic inside bearing housing and plastic bearing slides replace worn out bearing slides with new ones. needed 4 bearings direction suggested only two....

I noticed the original blower wheel was worn, the hole for the motor shaft was reamed out and the blower was not spinning with the motor. Air was not being circulated so the clothes were not drying well. Replacing the wheel was relatively easy. I did see other people commenting on the difficulty of getting the drive belt re installed properly. I noticed a small "lip" bent into the motor frame, and found the arm for the belt tensioner would fit into this lip and it held it out of the way while I reinstalled the drum and reouted the belt onto the motor pulley. Once the belt was in place, I gently let the tensioner out of its holding position and everything went back into place nicely.

I went to replace all four of the drum slides but in the process of doing this, found out that the whole of the top support had been rubbed away! I therefore ordered a replacement top support and replaced it per the instructions in the PartSelect webpage and from the youtube demonstration and completed the repair. I had a little trouble with getting the top support installed, but by jiggling it around and persistence I was able to complete the repair. The help I received on the webpage and video were invaluable! Thank you to PartSelect and to the other users for all your help!!

Unscrew the top panel parts three screws. Then another three or six screws to get to the dryer front which needs only to lift straight up about two inches. Pull back slightly and replace the teflon slides. To replace the slides they lay on a tiny plastic pin and slightly bend into the slot to hold them in place. Reseat the dryer drum. Reverse the process to make it like new. From the time you start hearing the dryer squeak, BE CERTAIN to replace these within a week or two (depending on usage.)Otherwise, you may wear out the housing where the teflon would rest. If that happens, you will be out more money to replace the housing and a lot more time to install. Been there and done that. Trust me.

Replaced drum bearing part and white slides.The problem was that it was not the drum slide support. It appears to be the the drum rear bearing of whch I am now ordering. The bearing replacement is a little more difficult, but I have taken this on as a challenge

Dryer would turn on when you pushed the "on" button, but as soon as you let go, it would turn off. Found the plastic door switch cracked (from slamming door closed). Unplugged the dryer. Unscrewed the two screws inside the top of the door to unfasten the top panel. Took the top panel off. Then unscrewed the two screws on the side to unlatch the front panel. Used plyers to take the 3 wires off the switch and slid the switch through the front of the door. Juat remember where the wires go. Then inserted new switch and connected the wires. Vacuumed out the dryer and reassembled. It took about 20 minutes and was easy! If I can do it, you can!!!

Removed top screws. Removed front panel screws. Removed front panel. Replaced worn slides. Removed drum. Replaced drum bearing and retainer. Cleaned lint from dryer, motor and blower assembly. Replaced light bulb. Door latch was purchased as spare. Inspected heating element. Re -assembled. Dryer now running like new again. I expect to have restring a new element in the near future. I like how the GE dryer comes apart. It is best to replace the slides before they wear all the way through.

inserted the latch into the opening in the front face of the dryer

There is a plastic female closure part in the dryer door that wouldn't close tightly around the metal male closure on the dryer. I popped out the plastic square with a screwdriver, popped the new plastic closure in with my thumb. Works great. I never even installed the new metal portion of the latch.

Unplug dryer, unscrew bulb then replace with a new bulb. Plug dryer back in.

replaced the parts that had worn out

Googled possible problem where noise was coming from. Went to Parts Select web site. Ordered felt and drum bracket. Removed screws behind control knobs and removed top of dryer. Removed two screws on front inside dryer (left/right side) this allowed me to remove front panel of dryer. Unattached wires. Drum bracket is located above door opening...pretty much snaps out, felt piece is located on bottom bracket. Felt piece was replaced and new top bracket replaced. Reattach wires, lift drum slightly to fit doo iInto place. Dryer still made noise. Noticed I did not have any drum slides! Drum slides slide into top of front bracket at 10/2 o'clock position and 11/1o'clock. Easy and very inexpensive dryer repair!! My husband was very impressed that I could take dryer apart and fix!!!

TOO EASY to repair. WORKS GREAT>

The repair was extremely easy to do. The video was perfectly done and described everything one needed to do in very simplistic details.

The clothes would get caught where the drum slide should be (it was almost totally worn down) and would leave black marks. I watched Parts Select youtube video. Bought the parts needed from Parts Select. They arrived within a couple of days. I replaced the 2 drum slides and no more getting caught. Took about 20 minutes.