DPSR610GG9WT General Electric Dryer - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Carol from Simpsonville, SC
- Parts Used:
- WE03X37317
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Rubbing noise while dryer was running
Removed too of dryer and placed the parts on. Runs like a brand new one. Thanks so much!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Thomas from Wake Forest, NC
- Parts Used:
- WE18X25100
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
old screen was not sealing properly
Replaced new screen in place of old one.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Patrick from Albuquerque, NM
- Parts Used:
- WE03X37317
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
Dryer was making a loud squealing noise.
I replaced the dryer bearing ( a plastic part) and all of the slides on the bearing. It now operates like new.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Adrian from Rutland, VT
- Parts Used:
- WE09X27634, WE03X37317, WE03X37318
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
not drying clothes, felt seal hanging in the dryer
Took dryer apart replaced felt seal and the four drum slides put it back together works better now than when it was new!!!!!!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Michael E from Victoria, TX
- Parts Used:
- WE03X29897
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- More than 2 hours
- Tools:
- Screw drivers
Dryer Belt Broke
After unplugging the dryer, I removed 2 metal screws up under the dryer sill rim, and removed the dryer top. Then, removed two more at the top of the front (door) section to remove it.
I wasn't careful enough when removing the door, and the wiring connectors popped loose from their connections. No harm done, though. Disconnect the wires once you remove the front panel.
I had to loosen the bottom metal screws on one side panel to have enough give to pull the dryer drum out.
The only way to replace the belt is to bend over the side of this unit and with one hand put the belt around the motor drive shaft, pull the tension pulley back, and put the belt on the wheel.
The hard part is working the drum back into place while VERY carefully slipping the belt into the drum goove. Many attempts were made only to have the belt slip off of the tension pulley or motor driveshaft. Be care full to turn the drum clock wise if the belt twists while working it into the drum groove. It was very disappointing to finally get the belt on, and work the drum back into place only to discover I had twisted the belt with the smooth side making contact on the driveshaft. Thus, I started over.
Aiming the drum into the back of the dryer is a tough task. I recommend a 1" X 4 " X 12" board to slip under the drum when beginning this process to help stablize, and guide the drum. It helped me tremendously, and was easy to remove out from under the drum once everything was back in place.
Use gloves. Yes, tough to work with in small places, and I did take them off to replace the belt around the tension pulley, however, there are too many sharp edges on the metal body of the dryer and especially the drum to do so without gloves.
Wires were easy to reattach and reassembly was smooth except for the top...check out the tabs, and spring tabs before you try and just plop the top back on. It goes a certain way...You'll know what i am talking about when you do this task.
I truly hope you have L O N G arms to do this task, and that the new belt lasts a long, long time!
I wasn't careful enough when removing the door, and the wiring connectors popped loose from their connections. No harm done, though. Disconnect the wires once you remove the front panel.
I had to loosen the bottom metal screws on one side panel to have enough give to pull the dryer drum out.
The only way to replace the belt is to bend over the side of this unit and with one hand put the belt around the motor drive shaft, pull the tension pulley back, and put the belt on the wheel.
The hard part is working the drum back into place while VERY carefully slipping the belt into the drum goove. Many attempts were made only to have the belt slip off of the tension pulley or motor driveshaft. Be care full to turn the drum clock wise if the belt twists while working it into the drum groove. It was very disappointing to finally get the belt on, and work the drum back into place only to discover I had twisted the belt with the smooth side making contact on the driveshaft. Thus, I started over.
Aiming the drum into the back of the dryer is a tough task. I recommend a 1" X 4 " X 12" board to slip under the drum when beginning this process to help stablize, and guide the drum. It helped me tremendously, and was easy to remove out from under the drum once everything was back in place.
Use gloves. Yes, tough to work with in small places, and I did take them off to replace the belt around the tension pulley, however, there are too many sharp edges on the metal body of the dryer and especially the drum to do so without gloves.
Wires were easy to reattach and reassembly was smooth except for the top...check out the tabs, and spring tabs before you try and just plop the top back on. It goes a certain way...You'll know what i am talking about when you do this task.
I truly hope you have L O N G arms to do this task, and that the new belt lasts a long, long time!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Robert from Salem, MA
- Parts Used:
- WE03X29897, WE25M40
- Difficulty Level:
- Easy
- Total Repair Time:
- More than 2 hours
- Tools:
- Screw drivers, Socket set
Rear drum bearing gone (only 4 years old). Decided to replace belt while I was at it.
I first watched the video on how to. Being mechecanically inclined I dismantled and removed everything needed to replace the drum bearing. Also removed belt at the same time. I replaced the bearing, then the belt. The belt could be a little tricky for some people. Getting the belt on the tension pulley could be a problem. What I did was I got a large nylon tie and put it around the armature of the motor. I then retracted the pulley just enough to be able to slip the belt over it. Of course this is all performed through the limited space on the bottom left, between the drum and the dryer shell. Once on the pulley, I cut the tie with wire cutters and it snapped into place. Rotated the drum a couple of times to line the belt with the pulley, perfect. I then put everything back together. I also cleaned any and all the lint that had gathered throughout the exhaust. Pluged the dryer in, perfect. Just like new. One more note getting the parts was so easy also. Your website and how to demo was a great help. Thank you, thank you very much. The words of the late Elvis Presley. They never get old.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Bruce from CHANUTE, KS
- Parts Used:
- WE05X20431, WE4M181
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers
Dryer was over heating and shutting off after like 5 minutes, the back was hot to touch..got the cycling thermostat problem solved
4 screws to open it up,pull out the wheel and there it is on back . Pretty easy..
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Sandra from Brazil, IN
- Parts Used:
- WE25X217
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Wrench (Adjustable)
I had to convert from natural gas to liquid propane
My son is an engineer and repairs washers and dryers for a large commercial laundry company on a daily basis. He installed my part easily and had me up and running in no time.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Ken from Westminster, MD
- Parts Used:
- WE25M40, WE03X37317, WE03X37318
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver, Screw drivers
clothes being eaten first then the loud noise
I replaced front and rear bearing.The rear I replaced because of cause and effect.There was some play so I am glad I replaced the rear too. Make sure you order drum slides. Ken
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Roger from HARTSVILLE, TN
- Parts Used:
- WE4M527
- Difficulty Level:
- Very Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
Timer stopped turning
Unplugged the old wire and connected new one at a time placed new timer back in position. Screwed cover back on and started drying clothes.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- CHRISTOPHER from PHENIX CITY, AL
- Parts Used:
- WE1X1192
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Pliers
I broke the door strike on the dryer.
Wife was out of town, visiting family. I broke the door strike by wedging the dryer door between the laundry room door, closed the laundry room door and it snapped the door strike breaking it. I ordered the part, and it shipped fast using the standard shipping, nothing fancy. Grabbed a pair of pliers and pushed the new door strike into place. It snapped right in, fits and works perfect like nothing ever happened. The wife will never know :)
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Peter from LEOMINSTER, MA
- Parts Used:
- WE05X20431
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
Bulb was intermittently working
Inspected door switch operation and was working properly and simply looked for bulb in the dryer drum housing and located it immediately above the door opening,unscrewed it and noticed the broken elements inside. The bulb is a 10w/120V. Installed bulb problem solved.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- victor from ST AUGUSTINE, FL
- Parts Used:
- WE18X25100
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
door filter
was no repair- removed filter from door and installed new filter into door. No tools required.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Jeffry from ROCKVILLE, MD
- Parts Used:
- WE05X20431
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
Burnt out bulb
Used a flash light to see, reached in and installed new bulb above the door
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Mark from Monroe Township, NJ
- Parts Used:
- WE05X20431
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Bulb
Open dryer door, reach in at the 12 o'clock postion
on the inside is the bulb.
on the inside is the bulb.
Was this instruction helpful to you?
Thank you for voting!