DHDSR46EG7WW General Electric Dryer - Instructions

The front panel has wear and tear, as was the drum bearing with broken pieces. To buy a new dryer would be several hundred dollars. A repairman told us it is not worth trying to replace the front panel. I found part select and ordered the required parts. All in all my cost is just over 200 dollars and I have a like new dryer. The front panel does not exactly fit my dryer (I guess my dryer is older) so I had to drill two holes to fit the bottom catch plate. I followed the video instructions. It was easy.

I am a 55 year old woman who likes to repair household items. I followed You Tube instructions and did it all by myself. A few screws to get the top off and a two more to remove the front piece. Trap duct assembly was cracked and falling apart. Pulling off the old was fairly easy. I watched the You Tube instructions on my Ipad so I could rewind and watch as I did it. The hardest part was I dropped one of the screws when placing the front of the dryer back on and had to find another one that was the same size. Luckily I have lots of old screws in my tool box, If you like to do small simple repairs to save some money this is an easy one.

Just took out of plastic wrapping and put on dryer. No tools needed.

-- Unplug dryer from electrical outlet
-- Open Door
-- Remove two screws going up into the top panel
-- Remove top panel
-- Close door
-- Remove two screws holding front panel
-- Remove Front Panel by turning out, keeping left side close to unit since wires are still connected.
-- Vacuum out all loose dust/lint
-- Tilt old Drum bearing toward you to remove.
-- Remove Old Felt Drum Seal
-- Install drum Slides on new Drum Bearing
-- Install new Drum Bearing, make sure it clicks into place securely.
-- Install new Felt Seal, make sure to push in far enough to securely hook to the clips on the bottom of the Drum Bearing.
-- Reinstall front and top panels
-- Plug in electrical
-- Dry

Pulled off old knob and snapped new one into place. Took about 5 seconds. Must be a lame design cause my dryer's less than 2 years old and the knob snapped on the inside and wouldn't turn. Easy to fix though.

Dryer is 3 yeras old. This dryer switch / start knob broke three times. First two GE repair fixed it. Charge was about $75 to $100. Then I found Parts Select, Who what great prices. Switch cost under $10. and took me 10 minutes to install. Dryer works great again. OH, I ordered an extra switch to have on hand.

Removed that to screws for that top first and door shake top little to that front and I took two screws on that top each side and removed that front and lint trap and install the new

I was using vice grips to turn the control knob (stub) until the new knob arrived. The replacement knob was a redesigned type with a metal backing plate to place on the control knob stub (better than the original plastic knob) however the diameter of the new knob is only half the size of the original knob and the mark on the dial does not line up with the markings on the dryer control panel making it difficult to know what cycle you are using or how far to turn the dial within each cycle before passing to the next cycle.

i follow your video and all went well except now the dryer will not heat. i went back on your site an tried the no heat option an still no heat

It turns out the back of my dryer timer knob was cracked, so everytime I would turn it it would just slip to any setting/time. This was just the matter of pulling out the knob & pushing in the new one. The other issue I had was my dryer would always run without having to start it. This is because the rotary "start" switch was bad. It just took a philips screwdriver to take the backsplash off the dryer to replace the switch. So easy my wife or kids could've done this!!

I read the other repair instructions on this site and looked at the parts diagrams. It wasn't entirely clear how everything came apart but once I started by unscrewing the top of the dryer and removing it (screws were just inside the dryer door) it was easy. Unscrewed the front panel next , swung it out, and it was quick work to install the new bearing with the slides. It wasn't too clear in the parts diagrams but I did need two each of the dryer drum slides and front dryer drum slides, four total, two on each side of the drum bearing. The dryer had been running on the old drum bearing itself, the old slides had worn completely down and the bearing itself was starting to disintegrate too. If I'd caught it sooner I could have reused the bearing and just replaced the slides. Saved a lot of $ and the dryer is nice and quiet again!

Son found out where the bulb was by using YouTube. I googled lamp for model number and your website came up. I ordered the part, it arrived promptly, and my son installed it.

remove the broken one and replace it with the new one

followed video exactly

I watched the repair video 3 times to make sure I was comfortable to do the repair.the video was very helpful.thank you ! Everything went well and the dryer runs great.