DCVH680GJ0MV General Electric Dryer - Instructions

Pulled the drum an found spade clip burned on wire. Hi limit Thermostat crumbled/ broke while pulling spade clip so I trimmed back the wire, cleaned the spade clip and soldered the wire back on. Isolated the other thermostats in the system and tested for resistance. Reassembled dryer.

Unplug the dryer. Remove top panel (remove two screws on the upper inside edge of the dryer door). Lift the front panel from front (tabs and slots at the back) and lift off. Remove the front panel (remove a screw from each side - top/front). Front panel sits on two feet at the bottom, tilt it forward from the top and lift it up (careful not to damage the electrical connection at the bottom left side). I found the dryer had another damaged part (plastic guide that the Slide WH and the Drum Slides connected to was badly worn). After ordering the additional part I attached the slides (white and gray) to the guide. Set the front panel back on the two feet and tilt it back into place (you'll need to slightly raise the drum back into position - easy). Replace the two screws that connect the front panel. Replace the top cover. The whole repair took less than 1/2 an hour including the time it took to vacuum out the dust. Total cost, about $35!

It's so easy, a caveman can do it! Watch the video on how to take it apart and while you have it open, grab a shop vac and clean around the area where you don't normally see. I replaced the top bearing since it was worn out pretty bad. The drum slides ( white and green ) which comes in pairs, were already gone. Put everything back together and works like new. No more squelling and vibration that sounds like my dryer was ready to come apart. Very fast on shipment. Thanks

1)

Watched a video online on how to replace the belt, it pretty much told me what to look for to get the drum out. Followed the instructions sent with the bearing kit and removed the old bearing assembly. Ran the screws supplied with the kit into the bearing assembly before I installed it. This was a tip I got off PartsSelect website. Running the screws in first is a must! Had my wife hold the assembly in place while I ran the screws in. That part of the job is the only time you need an extra set of hands. Put the dryer back together and it works like a quiet champ now.

I love the Partsselect.com youtube videos. The man in those videos rocks!!! I did the repair of my rear drum bearing kit exactly as he showed me in his video and it was perfect. I have spread the word on facebook and around work about Partselect.com and friends and coworkers are already checking it out. Hey, everyone loves a good thing. I suggest that you do not be afraid, you CAN do it. Tear that baby apart and save yourself some money.

First I took the dryer apart to see what the problem was and found that the felt dryer guide had come off it's mount and was broken. Next I saw that the dryer glides were worn away and if it was used much more it would have ruined the whole housing. I ordered the parts from parts select and to my pleasant surprise they were there in two days. The glides sit right over the door and just slip right in. The felt goes on the bottom under the door and sits in a plastic guide in which the felt is placed I tied the ends of the felt down on the ends with a piece of small wire to make sure they stay in place. It's been two weeks since my repair and there are no problems.

As I pulled each of the 3 bolts, I put a alignment rod into each of the holes. After I pulled the old deflector off, I had basically 3 pins/rods to slip the new deflector on and keep everything in basic alignment. Pulled one rod, reinstalled the bolt, so on and so on. Ran motor for noises or misalignment and had neither. Pretty simple repair.

I was teaching my associate how to do this repair so I showed him how to take off the top of the dryer. Then I showed him how to replace the drum slides. I had him clean out the dryer since we had it apart, and I also showed him how to remove the drum and then reinstall it. This was a very easy repair, and he learned a lot that he otherwise would not have known. Thanks for getting the parts to me so quickly. Rob from Clarks Summit.

replaced rear drum bearing kit Still makes the same noise

Removed the 3 star screws, putting in a piece if wire as I removed them. Wire was not stiff enough and let the drum slip thus binding making it hard to remove. Started over. Finally called a friend for help. I bought 3 tension pins the same size as the screws. When removing the diffuser screws, insert a tension pin in the hole as you remove each of the screws. The tension pins are hard metal and do not have a head. The diffuser will slip over them. After the diffuser was in place, we turned on the dryer to make sure it was running ok. I noticed what looked like lint toward the front. It was part of the felt gasket on the front of the drum and front of the dryer. We removed the screws on the dryer front and pulled it forward. The felt was rethreaded into its slot, put the front back in place,and replaced the screws that hold everything in place. If you turn the part of the dryer that spins by hand, make sure you are turning it in the correct direction. Turning it the wrong way is probably what caused the felt gasket to come loose causing more work.

Took off the top and front of the dryer---really easy, just two screws for each. Put new drum slides (4) on the front/sides of the drum. Then things got a little bit more difficult. Removed the drum entirely, vaccuumed everything out and had to replace the rear bearings. My husband did this part so I can't tell you exactly how he did it. Not too difficult though. The written directions from here were hard to read---need to make a new copy from the original as it's so copied that it's all smudged. Anyway, once we got the new bearings on, we put everything back together. Dryer works like a charm, at a fraction of the cost it would have been to get someone out to do it. Thanks a bunch for the fast service!

Your instructions were execellent
Problem is solve
Thank you

I ordered and replaced the front and rear bearings, including the slides that go on the front bearing. Most of this was un-necessary; replacing the slides would have been sufficient, and much easier to do. Two of the old slides were worn completely away.

First of all, I am a women...I read where it was probably my rear bearings so I ordered the part, it came in just right, then I replaced it put it all back together, and with the computers help, got it going, belt back on and all and then turned it on and walah it still made a loud noise. Shucks, so I read more and it said it could be the front bearings which I should have tried first but didn't read it first. Ordered part and put it on and wallah, that wasn't it. The noise sounded like the paper in a bicycle spoke so I checked the fan. There was the problem. The fan had so much dryer lint behind it it was forcing it against the housing making a noise. Cleaned it removed all the new unnessary parts and re-boxed them and put it back together but just before I put it together the door fell and two wires came loose so I plugged them back in and put the wrong one in the wrong place cause when I plugged the dryer in sparks went everywhere!!!! I need a man now!!! Scared of electricity!! Sure wish I knew if the noise was fixed :).