DBXR463PG4WW General Electric Dryer - Instructions

Clips on the inside of the door handle had snapped off, 1 minute later it worked like new. NO TOOLS required! So happy my older appliances can have new life by the parts carried by PartSelect. Thanks!

I first unplugged the unit, opened the top, disconnected and took off the control panel, took off the front panel to determine the source of the squeaking noise coming from the Dryer. I saw that 3 of the 4 Front Drum Glides were gone and the drum had worn away significant amounts of plastic from the Top Bearing Assembly. I purchased the Top Bearing Assembly and a set of 4 Front Drum Glides. Disassembled the damaged parts and reassembled with the new replacement parts. The reassembly took less than 20 minutes. I plugged in the Dryer and viola! It works as good as new.

remove top of cabinet and front panel. placed belt around drum and replaced idler pully placed new belt around pully and was done. not a hard job at all. replced front panel and top. thanks to a speedy delivery of my parts dryer was only down two days.

Took apart by removing the top and front panel. Found drum rubbing due to worn glides and felt.

My husband broke the door handle, but of course, i had to be the one to order the part & fix it. I ordered the part on the weekend and much to my suprise it was on my doorstep on Tuesday when I got home from work. Then I saw the part was shipped from nearby Louisville. I was overly happy with partselect!!!!! All I did was open the packaging and clip the dryer handle into the 4 holes. Easy as pie!!!!

opened up the control cover, pulled off the 3 wires to the switch. unclipped the swutch from the panel and reinstalled the new exact replacemnt sww you sent

I first removed the the timer knob and the other ones from the front of the control panel. Then I removed the three screws that held the rear access to the control panel. Disconnected all wires to the timer keeping written info to which wires went to which terminal. The replacement timer was exactly like the original in the placement and designation of the terminals. I then twisted the bad timer out of the plastic holders, placed the new one and twisted it in place, and replaced the wires. I then replaced the screws in the rear of the panel and replaced the knobs. It did not take much longer than writing this. Very easy and I am completely satisfied.

Shut off the Electric at the breaker panel. With a Philips head screw driver took off the metal plate, and slide the backsplash out of its holders. Twisted the three switches, twisting to the left to remove them and replace the back splash, controller, timer switch and installed the new rotary switch with a right twist. There are three wires on the rotary switch, just follow the line of the old switch. Replaced the back metal panel, and turn on the breaker. Replacement takes about 30 minutes along with putting the dryer back in place.

This kept the interlock open and shut off the dryer when the door swung open The broken latch was popped out using a flat blade screwdriver and the replacement snapped into place by hand. Good as new!

The video of the dryer lint chute assembly showed the man without gloves. I didn’t wear gloves. When I disconnected the wire from the front panel assembly, my hand jerked and hit the side of the panel. It must have been razor blade sharp, because I got a deep cut. Advise people to wear gloves to protect hands from sharp metal.

Pulled the unit all apart to replace the rear drum bearing. Also replaced the front bearing. Works like brand new. Easier then I thought

First, I removed the 2 screws for the top panel, lifted the top panel off, then I removed the 2 screws holding the front panel, tilted it forward to clear the drum, disconnected the door switch and set the panel aside. I then installed the 4 slides on the new front bearing, removed the light socket from the old bearing, removed and discarded the old bearing. I installed the light socket into the new bearing and the bearing assembly snapped into place on the front panel. I then re-connected the door switch, aligned the front panel with the drum, secured the front panel with 2 screws, then carefully placed the top panel back in place and secured it with 2 screws. I checked the rotation of the drum and it worked like a champ. Matter of fact, that same day I put this dryer and a matching washer up for sale at 8:30 am on October 31st and by 9:20 am I already sold them!! I delivered and hooked them up and the dryer works great!!!

Just slipped it on. No problems, No Tools.

The inner piece of the knob cracked so it just spun on the dryer shaft it's suppose to turn. Ordered a new knob, slipped it on and all works great again now.

I had already replaced the four (4) small wear strips which were like short strips of teflon, and the squeaking decreased almost completly. I noticed that front side of the drum itself had started to wear through the actual plastc drum bearing, but I hoped having previously replaced these tefon strips that would be the overall fix.
Wrong again... after a few weeks the squeeking continued until I ordered the new drum bearing and replaced the worn one with the new one. I was able to re-use the previous teflon wer strips, and it's like new now at least the squeaks are gone,

The actual fix was a very simple remove old drum bearing, snap in new drum bearing install old teflon wear strips put four screws in top, and front panel and I was back in business