DPVH890GJ1MV General Electric Dryer - Instructions

Replaced drum bearing part and white slides.The problem was that it was not the drum slide support. It appears to be the the drum rear bearing of whch I am now ordering. The bearing replacement is a little more difficult, but I have taken this on as a challenge

Dryer would turn on when you pushed the "on" button, but as soon as you let go, it would turn off. Found the plastic door switch cracked (from slamming door closed). Unplugged the dryer. Unscrewed the two screws inside the top of the door to unfasten the top panel. Took the top panel off. Then unscrewed the two screws on the side to unlatch the front panel. Used plyers to take the 3 wires off the switch and slid the switch through the front of the door. Juat remember where the wires go. Then inserted new switch and connected the wires. Vacuumed out the dryer and reassembled. It took about 20 minutes and was easy! If I can do it, you can!!!

Removed top screws. Removed front panel screws. Removed front panel. Replaced worn slides. Removed drum. Replaced drum bearing and retainer. Cleaned lint from dryer, motor and blower assembly. Replaced light bulb. Door latch was purchased as spare. Inspected heating element. Re -assembled. Dryer now running like new again. I expect to have restring a new element in the near future. I like how the GE dryer comes apart. It is best to replace the slides before they wear all the way through.

Faulty Door switch. Dryer would heat up so I knew it wasn't thermostat or element related.

After some research on the internet, I deduced the squeaking sound in our dryer was due to defective drum glides. I ordered a set of four of the white type, knowing only our model requires four glides, but not knowing there are two types for two locations. After disassembling the dryer I realized I needed more parts - two green slides and a new top bearing assembly. The dryer drum had eaten thru glides and into the plastic assembly. That was the reason for the squeaking noise - metal sliding against hard plastic. I ordered the additional parts directly from the manufacturer to ensure I got it right. After all the parts arrived, the repair was easy and took less than 30 minutes. I actually had my 17 year-old daughter do the work to teach her some skills. I just instructed her and stepped in on assembling the top that was just a bit tricky to put back on. Problem fixed.

Originally ordered heating element kit, but decided to replace drum slides and "o"-ring while the dryer was dis-assembled.Replacing the dryer elements was relatively easy-just follow instructions. Replacing the slides and o-ring was very easy, just clip in place. The dryer vent was almost totally clogged and probably the cause of most problems. This took longer than all mechanical repairs as I have a long dryer vent. I suggest cleaning the dryer vent regularly to avoid problem. I used a 4" circular brush and cordless drill to clean the duct. If you have not cleaned your vent in 2-3 years, you will be amazed at the amount of lint build-up. I was very pleased with the price of parts and customer service at Parts-Select, estimate I saved approximately $250-300.

It took a while to diagnose the problem. I finally figured out it was the door switch by pushing it with my finger with the dryer door open and starting the dryer. It would run like that, but the switch was not being pressed in enough by the door. I ordered the switch and I should have been able to replace in about 15 min. But the old switch broke while I was removing it and it fell back inside the unit. So I had to remove the top and the front panel to access the door switch. That's why it took so long. If that had not happened it would have been a much simpler repair.

I followed the varied instructions out there for getting the dryer open. WATCH the videos on uTube; I took out more screws than needed on first attempt -- which isn't a big deal but took me longer than it should have to pull it apart. It appeared the grinding was coming from the dryer bearings due to some abrasion I could see and worn front slides, so I replaced the front slides (4) and the rear bearing. The kids helped by crawling inside the drum to tighten the new bearing bolts (just for fun). When I put it back together it was making a somewhat different grinding noise. It wouldn't make any noise until I put the belt AND front cover on and then it would make a periodic (about every 10 degrees) grind when I rotated the drum; I took it apart and the grinding would stop even if I rotated the blower by hand. Put it together, the grind would start .... It took me awhile to figure out that the blower retaining bolt had come loose so the plastic blower was grinding on the metal cover. CHECK THE BLOWER RETAINING BOLT visible from the front with the dryer door/cover off -- it's not obvious that it's loose by looking at it since the retaining clip still sits over the blower shaft even when it's loose. You might even see small nicks in the blower fan blade. It's super quiet now.

Followed the Part Select video instructions which made the repair really easy!! Thanks for a job well done! ALSO.. the drum wobble was not caused by worn slides and felt. There are three screws holding the drum axle flange. Two of them fell out leaving the drum to flop about as it rotated. So we scavenged some screws from elsewhere on the dryer and problem solved. Once again.. thanks to Part Select for great instructional videos and great customer service ordering parts.

inserted the latch into the opening in the front face of the dryer

Replaced bulb.

To get to where the drum slides go you have to first remove the dryer top. Then you have to remove the two screws that hold the dryer front/door. Found inside the dryer about an inch down on both sides. Be careful because it will fall off. Lower carefully as there is an electric hook-up on the bottom of the door. On the door top are the brackets that the slides slip into. My dryer has 4 slides. Sold individually for some reason. You are done except for re-assembly. Slip dryer drum back on door, press the front until you hear it click back together. Put screws back in and top back on. You are done and no more screeching!

The repair was extremely easy to do. The video was perfectly done and described everything one needed to do in very simplistic details.

replaced the parts that had worn out

Googled possible problem where noise was coming from. Went to Parts Select web site. Ordered felt and drum bracket. Removed screws behind control knobs and removed top of dryer. Removed two screws on front inside dryer (left/right side) this allowed me to remove front panel of dryer. Unattached wires. Drum bracket is located above door opening...pretty much snaps out, felt piece is located on bottom bracket. Felt piece was replaced and new top bracket replaced. Reattach wires, lift drum slightly to fit doo iInto place. Dryer still made noise. Noticed I did not have any drum slides! Drum slides slide into top of front bracket at 10/2 o'clock position and 11/1o'clock. Easy and very inexpensive dryer repair!! My husband was very impressed that I could take dryer apart and fix!!!