DBXR463PG4CC General Electric Dryer - Instructions

I removed the two screws that hold the front panel to the top panel. I removed two more screws that hold the front panel to the side panels. I separated the front panel from the side panels and removed the drum.

I could see on the front panel the drum slides were badly worn. One was gone.

The new parts installed easily using no tools at all. Everything snaps in place. The new foam gaskets press and stick to seal the duct work. The felt strip pressed into place.

I replace all the panels in reverse order and plug it in. It operates fine, but the motor is making the noise. I will look into replacing the motor next.

Removed the top of dryer two screws behind door at top then removed top two screws top corner lift dryer tub put belt around the tub then looped belt around the pullies.

First I figured out it was the start switch, I heard it make an electrical zap noise when I turned it and then the dryer didn't start. Once I had the part I simply removed the back from the dryer with a screwdriver (5 phillips head screws and 1 flat head). Then I twisted the old switch and it popped right out. Then I unhooked the wires and rehooked them to the new switch. Then I twisted the new switch into place, tested the dryer - IT WORKED! After that I just replaced the back cover and I was done. It was so quick! I am a 25 year old single mother with a 21 month and 4 month old. If I can do it on my own anyone can!

1 Unplug power cord. 2 Remove top and front panels. 3 Remove old bearing, slides and bulb. 4 Install new bearing slides and bulb. Reinstall front and top panels. 5 Restore power and test. Time to repair 25 minutes. Very satisfied with the parts and the time to receive them, very good parts service. Will definately use this service in the future and will highly recommend this company.

Doing some simple troubleshooting with the volt-ohm meter I determined that the door switch was failed.

The replacement door switch restored the motor circuit keeping my dryer in action.

Pulled the front of the dyer off, snapped old bearing off, snapped new drum bearing in, affixed 2 new slides and 2 new other widgets (5 pieces total). Vacuumed/cleaned out various bits and pieces before i closed her up.

No squeaking.

Called a priest, but he died. Now i just do whatever the demon says, but i do it with quietly dried clothes.

easy no problem

A very easy fix. Opening the front door to the dryer locate two chrome phillips head screws in the upper part of the door opening which hold on the top of the dryer. (I think in the older dryers the top simply was held on with keepers and you could simply pry it off. Not the case here)Lifting up on the front of the top it comes away from the back control panel. I would recommed that the control panel be removed as it is necessary to remove it to put the dryer top back on due to three clips that wont allow you to put the top back down with the control panel in place. It takes a star wrence to remove it. Once the top is off ther are two phillips screws holding the front of the dryer on (one on each side) remove them and the whole fron lifts up and off. The drum rides on a plastic schroud attached to the dryer inside front. Mine was so worn it required the purchase of the entire assembly which comes in two parts. The upper part had worn away so badly the drum was riding on the metal causing the noise. I ordered both the upper and lower assembly and both just simply snap off and the new ones snap right back on. No tools. I was a bit dissapointed as I assumed that the felt which is located in the lower assembly would come with the new part however it did not nor did some plastic tabs which the drum rides on in the upper assembly comes with the replacement part. It takes four of those tabs so order appropriately. Went back together easily and the whole job was done in about 40 minutes.

straightforward swap, just form the top rail and click it in

First, let me say that my repairman said the bearing and slides would cost between $150-200, and the total repair would be pushing $400, so we should just get a new dryer. Well, the total cost for the parts was less than $50.

The installation was easy.
1. Remove the two bottom screws of the door hinges, loosen the two top screws, and remove the door.
2. Unscrew the two screws, under the upper lip of the door opening, that secure the front panel to the top panel.
3. Pull the front of the top panel up, and then pull the panel off.
4. Remove the bulb from the front panel.
5. Unscrew the two screws, from inside the dryer, that secure the front panel to the frame.
6. Pull the front panel away from the drum and frame. Had to lift the drum slightly to do this. The electrical connection wire was still attached to the front panel.
7. Slide off the old drum bearing from the inside of the front panel.
8. Insert 4 new slides onto the new bearing.
9. Slide the new bearing onto the rim of the opening in the front panel.
10. Reset the front panel back into the slots at the bottom front of the frame, with the bearing fitting into the drum. Again, had to lift the drum slightly to do this, and make sure the wire was not caught between the front panel and frame.
11. Re-secured the front panel to the frame with the two screws.
12. Replaced the bulb in the front panel.
13. Replaced the top, and re-secured it with the two screws.
13. Put the door back on.
Quiet dryer once again! And saved the $800, including installation, a new gas dryer would have cost us!

The problem was intermittent. It only happened when the unit was first started. After it was restarted it usually worked until the load was dry. I looked at the schematics and saw that only the hi-temp therostat and the motor overload could stop the dryer completely. I put my volt meter on the hi-temp thermostat and ran the dryer. When the dryer stopped I realized the hi-temp therm. was tripping. I read the web site help for this symptom and the suggestion was the bias therm.
I replaced it and the unit worked.

5 minutes! loosened 4 screws pulled front off replaced bearing, felt, and slides. put everything back together, tightened screws. Worked like a NEW ONE!!!!

I removed the door and "flipped" it to open right to left. Rather than remove the existing door latch I added the purchased latch on the right side to enable opening the door right to left or left to right.

I removed the top of the dryer (unscrewed from the inside to release the top). Removed interior screws to pull open the front of the dryer. Once inside, it was really visible that the old parts (front air duct top and bottom) were in bad shape. They were cracked and broken. I removed the old pieces (they pretty much cracked and crumbled right off). I snapped in the new pieces careful to avoid damaging the electrical connections and wires. Once snapped into place (top and bottom), I careful put the front back into place making sure that the dryer drum rested on the new pieces. All screws back in place and all done! Dryer is now working as new!!!

Pulled out the remnants of the old latch out with the pliers and then popped the new one in...less than 2 minutes. Oh, and the part was delivered in less than 2 days. Great job, Partselect !