DDC4400SLMWH General Electric Dryer - Instructions

My husband and I had taken apart this dryer before, so the second time was a lot easier. The first time we took it apart it took 2-3 frustrating hours. So, if it's your first time, plan for longer.

1. Before we started anything we unplugged the dryer and disconnected the vent.
2. We removed the top and loosened the contol panel on top.
3. We removed the front. Be careful of the wires. You can label them, or just remember where they go.
4. Lay the dryer down on it's back. This make's it easier to remove the drum.
5. Remove the drum, but gently slide the belt off first. Don't stretch the belt removing it.
6. Once the drum was removed, we removed the screws from the inside of the drum.
7. We didn't need to use the entire kit, just the part that sits in the center and spins...kinda looks like a top. (Yes, that's my technical description)
8. We screwed in the new "top" and put the dryer back together.

Really the only part I had to help with (this time)was putting the drum back in to make sure it sat where it was supposed to. It made a big difference that it was laying on it's back...we didn't do that the first time, which was part of our frustration.

Putting the belt back on is a little tricky too. We had instructions still for our dryer to refer to put it back on. If you don't have yours, just google or bing for the instructions. There's website's out there with great pictures.

Pulled the drum an found spade clip burned on wire. Hi limit Thermostat crumbled/ broke while pulling spade clip so I trimmed back the wire, cleaned the spade clip and soldered the wire back on. Isolated the other thermostats in the system and tested for resistance. Reassembled dryer.

open door, remove two screws from below the top. gently remove the top from the side and bottom panels. remove two 5/16 screws from front panel hold panel so it does not fall. the bearing assembly will come out by moving the bearing towards the dryer, and pulling upwards. replace with new bearing, use 4 front dryer slides and reinstall the top and front panel. can be done in less than 15 minutes

The parts came very quickly, and they were the exacxt parts which made installation very easy.
Just open the dryer door, there are 2 screws to remove right above the dryer door that holds the top plate of the dryer. slide the top of the dryer top off by pulling up and ouyt towards you. There are 2 screws that hold the front of the dryer, remove the 2 screws and the front of the dryer will come out towards you. The drum will fall a litttle towards you.
I let the dryer front lean on my leg and snapped out the bearing and drum slides replaced it with the new one. Reverse the order of taking it apart
Now my dryer sounds as quiet as the first day I bought it.

Pull the old lint trap out. Slid new one in

We had a squeeking sound coming from our dryer which I felt was probably the belt. When I removed the front of the unit and saw the condition of the slodes and drum bearin, I ordered a set from PartsSelect.com. It only took about 20 minutes to repale the parts, and 5 of that was figuring out the bearing just "snaps on" (I was afraid to just yank it for fear of breaking something else). Probably saved like $75 or so between the parts markup and a service call by doing it myself.

After removing pieces that were stuck in the door, I simply popped the new handle in place. It took less than a minute. What was the easiest was ordering and receiving the new parts- I ordered and 2 days later I received the new parts. I didn't expect to get the new parts for at least a week.

inserted on an angle and snapped in place.
The best part of this story was I ordered the part on a Saturday and got it on Monday evening.
The repair took less than 20 seconds. I am extremely impressed with the fast fast fast shipping time.

It went perfect , just put it in. No tools needed.

I ordered the part via the internet. The shipping date was delayed twice but you excellent customer service department followed through and expedited the order. I installed it myself. Thank you.

Watched a video online on how to replace the belt, it pretty much told me what to look for to get the drum out. Followed the instructions sent with the bearing kit and removed the old bearing assembly. Ran the screws supplied with the kit into the bearing assembly before I installed it. This was a tip I got off PartsSelect website. Running the screws in first is a must! Had my wife hold the assembly in place while I ran the screws in. That part of the job is the only time you need an extra set of hands. Put the dryer back together and it works like a quiet champ now.

Snapped on new handel. Took all of 5 seconds. The hardest part was finding the part, which your website took care of....Thanks!

Simply pulled off the old handle and snapped in the new one! No tools required. Took about 5 seconds!

I broke the handle

This one is so easy my grandson could do it. The removal was easy, it broke off. The installation was a "snap in place". Thinking I needed a few days of dryer use without the handle, I made a temporary repair. I fished some heavy packing string thru the slots in the door, made a loop, than a knot. This gave my wife something easy to grab to open. Did not even need to do the temporary repair, the part arrived in one day.