DS4500EA1WW General Electric Dryer - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Earl from NORWAY, ME
- Parts Used:
- WE1M654
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Pliers
The knob cracked and a piece broke off.
Pulled a little piece off dryer and replaced it with a new dryer knob. Very easy and quick.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Bruce from ELVASTON, IL
- Parts Used:
- WH01X10060
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
On knob went bad
Took new one out of package, and push it on. 4 seconds!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Maria from MIRAMAR, FL
- Parts Used:
- WE1M654
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
Replace a broken timer knob
I just put the piece in place and it fit perfectly. I didn't need a tool for the installation.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- James from YARDLEY, PA
- Parts Used:
- WH01X10060
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Pliers
Broken knob and could not turn on dryer
followed the video you provided and it was easy!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Alan from BELFORD, NJ
- Parts Used:
- WE4M415
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
Switch not working.
Open the door and removed the part. Installed the new part and started the dryer.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Margaret from SCOTTSDALE, AZ
- Parts Used:
- WH01X10060
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
My dryer wouldn't start, I saw the part on your website after reading comments from other people
I put the nob on the post, one side is flat the rest of the lever on the dryer is round. So I matched up the lever with he inside of the new knob and slid it on . The dryer works perfectly. I ordered it on May 5 th and the nob arrived May 15 th. I guess Georgia is a long way from Arizona. But the part fit perfectly and I am happy. Thankyou.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Sally from MANHATTAN, KS
- Parts Used:
- WH01X10060
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
The Start knob broke off
At first the knob seemed like it would not fit on, but after I sprayed it with WD-40 oil, it slipped with a gentle, steady push
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Bernice from INDIANAPOLIS, IN
- Parts Used:
- WE1M654
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
dryer would not turn on
ordered knob ,. pushed it on.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- James from INDIAN SPGS, AL
- Parts Used:
- WE1M654
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Pliers, Screw drivers
Timer knob and shaft had stripped
Replaced switch by taking out top 3 screws in back of control panel. Hold new switch in one hand and took out wire(female discount) one by one as they matched old switch. Put back in holding slot, screwed back together, DONE. If I had someone help it wouldn't have taken 10 minutes
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Manuel, J from MCALESTER, OK
- Parts Used:
- WE4M325
- Difficulty Level:
- Very Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
Original terminal grounding block melted for unknown reason.
Unscrewed the old, screwed in the new making sure wires matched up same as before. Reset my breaker and works like new again.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- LARRY from HAMILTON, OH
- Parts Used:
- WE4M325
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Pliers, Screw drivers
When moving the dryer there was a loud pop and the dryer circuit breaker tripped.
When the dryer was installed last year by the dealer, one of the hot leads was not screwed down tightly. Over time the screw loosened and began to arc causing the plastic holding the screw to melt. When I moved the dryer the hot lead fell off and hit the terminal block cover shorting out the dryer. I was able to locate the exact terminal block I needed with their helpful dryer section diagrams. The part came in the time they said. I took off the old terminal block with just 2 attached screws. i kept track of which screws held the hot and neutral conductors and the ground before I removed them. I was then able to slide on the dryer wires and attached the home conductors. I put on the cover plate, turned on the circuit breaker and it worked.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Larry from Naples, FL
- Parts Used:
- WE11M23
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 1- 2 hours
- Tools:
- Screw drivers
Low heat
I bought the Heating Element and Housing together so that I would not have to stretch and run the coils and to save time!
1. I removed the two screws that hold the top down by opening the dryer door and removing the two screws at the top of the door opening. Then I pulled the top off.
2. Then I removed the two screws on the top inside of the dryer on the left right and took the front off.
3. Next I spread the dryer open a little and pulled the drum out while pushing the belt off the back of the drum.
4. Then I removed the screws to the sensors and removed them from the housing.
5. Then I removed the four screws holding the heating element housing to the back of the dryer and took it out and put in the new peace.
6. Do everything in reverse when putting the dryer back together.
1. I removed the two screws that hold the top down by opening the dryer door and removing the two screws at the top of the door opening. Then I pulled the top off.
2. Then I removed the two screws on the top inside of the dryer on the left right and took the front off.
3. Next I spread the dryer open a little and pulled the drum out while pushing the belt off the back of the drum.
4. Then I removed the screws to the sensors and removed them from the housing.
5. Then I removed the four screws holding the heating element housing to the back of the dryer and took it out and put in the new peace.
6. Do everything in reverse when putting the dryer back together.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- James from Troy, OH
- Parts Used:
- WE1M654
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Timer knob hole split
I ordered a new knob. The new knob was not broken, so it all worked out great.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Kaye from Boones Mill, VA
- Parts Used:
- WE1M654
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
This is the 2nd replacement timer knob
So simple....just put it on! Sure beats paying a $65 service charge (which we did the 1st time). Have a feeling that I'll be ordering another one.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Shirley from ASHEBORO, NC
- Parts Used:
- WE1M654
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
The Knob broke.
Just put the new knob on.
Was this instruction helpful to you?
Thank you for voting!