DBL333GY0AA General Electric Dryer - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- John from Granbury, TX
- Parts Used:
- WE03X10001
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers
Clothes snagging and getting stained in dryer
Hardest part was getting the top off which ended up being quite easy, once I knew how. At the front of dryer, between the top and the cabinet, there are two spring clips that hold the top to the bottom. I could feel them with the putty knife but wasn't sure how to release them. Push on them with the blade of the stiff putty knife ... push hard and they will release. When the top was off I could see the screws that held the front. I unscrewed those, had easy access to the front glide that needed to be replaced. Pulled the old one off, followed the directions to glue the new one on, gave it about an hour to dry, reassembled and away we went. No more snagging.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Jonathan from Chanhassen, MN
- Parts Used:
- WE4X881
- Difficulty Level:
- Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
The control switch broke off flush from the start switch
My wife was attempting to start a load of laundry when the start knob came off in her hand. I figured the inside of the knob had broken loose and the stem from the rotary start switch would be sticking out, well the stem had broken off flush and the knob was fine. After ordering a replacement, I jerry rigged the broken one with a large screw driven into it and put it back in place, worked great, just had to put a screwdriver into the screw and turn it to get the dryer to start. I felt it was fine to stay that way but the wife insisted we install the new one to put the knob back in place. The new switch arrived very quickly and went into without a problem, just four screws to remove the panel, two wire connections and was working again.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Linda from Clermont, FL
- Parts Used:
- WH1X2721
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Selector knob broke off
I ordered a selector knob and it was delivered in a short amount of time. I wasn't sure if it was the right one when I ordered it, but my husband just put it right on the dryer. He said it was perfect. Thank you PartSelect!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Edward from Garrison, NY
- Parts Used:
- WE4X881
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Pliers, Screw drivers
there was no problem
installation exactly how your directions told me on the computer
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- DERALD from Burleson, TX
- Parts Used:
- WE4X881
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Switch was either stuck in start position or had to rotate full turn to start
Removed four allen head screws to expose inside of panel. Used flat blade screwdriver to raise spring retainer and turned switch counter clockwise to remove.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- frederick W from wall, NJ
- Parts Used:
- WE25X10001
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers, Wrench set
Broken shaft in rear bearing
Take the top off and front off and disconnect the belt and lift the drum out and there it is . Easy and alot cheaper then new dryer and works like new .
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- wesley from mcleansville, NC
- Parts Used:
- WH1X2721, WE03X10001
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers
drum was making noise and clothes wer getting hung between drum and outer panel
removed top panel of dryer, then removed the outer panel where the door is. glued new drum glides on and now it works great
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Michael from Rahway, NJ
- Parts Used:
- WH1X2721
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Broken Start knob
After finding a matching knob for the broken one on my dryer, I ordered it from this website and within days had my dryer working like new again. Just slipped it on and that was it. No more using pliers to start the dryer. Couldn't have been easier.
Was this instruction helpful to you?
Thank you for voting!
Stem of Rotary Start Switch broke off
Fairly simple. removed start wwitch by rotating it out of its position. There is realy only one way to remove it and it is intuitive. The new part is simply placed n the only position that the part will fit in the panel. Once the part is locked in placed, the new part is installed. Simply take you time and think it thru.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- David from Rice Lake, WI
- Parts Used:
- WE4X881
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver, Screw drivers
Broken start swithch from moving dryer
Removed top panel from dryer. Unplugged the 2 wires for swithch, rotated swith, and removed. Reversed the process. Put parts back together.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Walter from Boone, NC
- Parts Used:
- WH1X2721
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Dryer Start knob was broken
Ordered new knob from you people and simply replaced borken knob.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Joyce from TUSCUMBIA, AL
- Parts Used:
- WH1X2721
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Broken starter knob
Just pushed the knob on by hand and it was ready to start! It was great not having the extra expense of a house call! Thank you!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Alonso from MONTGOMRY VLG, MD
- Parts Used:
- WE12X10009, WE13X10011
- Difficulty Level:
- Easy
- Total Repair Time:
- 1- 2 hours
- Tools:
- Screw drivers
Rear bearing was broke
I like to fix , i have time and i just give me the chance to try , and i did it , i wish to pay less for the parts , but was a good feeling when the problem fixed
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Linda from Levittown, PA
- Parts Used:
- WH1X2721
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
missing knob
the part fixed all the problems in a cinch
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Catherine from Dunmore, PA
- Parts Used:
- WH1X2721
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
dryer wouldnt start
just replaced the old knob
Was this instruction helpful to you?
Thank you for voting!