DBL333EB1WW General Electric Dryer - Instructions

Just push knob on less than 4 seconds

This was done to a washer/dryer that is in a closet and was worked on in place and not removed so it was all done through the front. Its a good idea to vacuum the inside out before putting it all back together. 1.Remove all of the screws that hold down the top of the dryer and remove top. 2. Remove the front slanted panel below the controls then Remove the two small black screws holding the plastic inserts on the left and right sides of the controls panel plus the two silver screws that will allow it to drop so that you can access the tabs that hold the front section on. 3. Remove screws holding the front section with the door on. The last two will be tabs at bottom that were hidden by control panel. Unplug connector and remove front. 4. Note how belt is positioned around motor and tensioner before removing belt.(just push tensioner until belt is loose enough to slide off of drum to remove belt). 5.Slide out drum and remove old bearing and replace with new one. Be especially careful tightening the three screws that attach the bearing as they are easy to strip. 6. To remove the bushing at the back of the dryer you will remove the two screws. but you will need to hold the clip on the back of the dryer or it will drop when the screws are removed. When re-installing MAKE SURE not to lose your ball bearing that the drum bearing will rest against. I used a strong small magnet to hold the ball bearing against the back of the nylon cradle bushing so I wouldn't lose it when re-installing the bushing and it worked great. Once the nylon bushing was back in place I lubed it thoroughly and put everything back in reverse order. I usually would not fill out one of these do-it-yourself forms but the instructions that are already listed with this part are completely different from what I encountered up to the actual bearing and bushing replacement. Hope this helps.

It took about 20 minutes, first I popped the top off using a flat screwdriver in my leatherman and removed the wires on the door switch then two screws holding the front on, and then I removed the drum which took a little longer because the belt tensioner was difficult to release because of limited space. Removed old bearing (ball and socket) and replaced with new one. I then reassembled in reverse order. Working great. . .

I turned off the power, unscrewed the 4 screws from the top of the dryer. I then opened it and turned the switch that was in there counterclockwise exactly as utube video said to do. I then took off the two wires from the old switch. The rotary start switch fix right in where the old one was. I put the panel back together, put on the old knob and turned the power back on! It took less than 15 minutes from start to finish! If I can do it anyone can! Joanne Klinkhammer Cecil, Wisconsin

It took longer to vaccume the lint out of the machine than to change the part.

The part replacement is done without any tools.

My wife could have done it

We are a retirement community and when we opened March '07 the company purchased GE washer and dryers to go in our common area laundry rooms for the residents to use. Because of their age, they will often turn the knob counter clockwise and not the right diirection which breaks the device which is not good. With in 3 days of installation they had broken 2 of the new knobs.
But, the ordering was simple, the shipment was fast and the install was quick for the maintenance tech.

Removed the Drum and replaced the part....

I followed the video instructions. I did have to run to the hardware store to pick up a torx screwdriver but otherwise the instructions were perfect. I generally hire someone to do repairs, but this was too easy! I highly recommend doing this yourself as it is definitely a time and money saver. The website made ordering easy and the part arrived quickly!

Remove the top of dryer, remove switch after two wires removed. Snapped in new switch and hooked wires and then put top back on.

The old knob broke off & was no longer able to turn the pin to start the dryer. I simply slid the new knob onto the pin & it worked like new.

Took the knob and clip off the dryer and stuck the knew knob on!

Used pliers to remove old clip. Installed new clip and knob. Very easy.

Disconnected the power removed 4 screws from top panel. Removed 2 wires, turned switch counter clockwise. remopved switch. Replaced with new switch,connected the 2 wires, put panel back inplace,put screws back in panel,plugged dryer back in. SUPER SIMPLE Total time 5 minutes

Checked all thermostats, they were good. Circuit was getting 220 vac. Eventually found fuse in the back near the heating element, same was bad. By-passed same, and when we did, the timer Popped & arched !. Not sure why. Motor protectrion fuse found to be good. Heating elements good. Fuse was the only bad part found, never figured out what caused it to blow. Appliance was taken away after purchase of new one. Problem not found or resolved by self diagnostics. Originally the exhaust duct was somewhat clogged with lint, but not severely.

Had a slight problen at first getting the part that I needed. Because of not knowing the model # for the washer/ the label was still on the lid of washer but the # was completely washed off. I thought I needed the complete timer/knob. I am 80 and a neighbor showed me what the problen was. Almost all of the plastic teeth were worn off.I finally found the Model # on the original purchase bill then order the knob only. My husband (86)thought I should have soneone put the new knob on but i pulled out the old clip and the new knob slipped right on. Thanks to all of your staff that helped me. Wonderful service.