DVL223GB1WW General Electric Dryer - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- GARY from HALEYVILLE, AL
- Parts Used:
- WE3X70
- Difficulty Level:
- Difficult
- Total Repair Time:
- 1- 2 hours
- Tools:
- Screw drivers, Wrench (Adjustable)
Lack of grease caused bearing to go out
I took the top and front off the dryer. I then took the screws out of the drum and removed the drum. I then took the old bearing out and put the new one in.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- William from Fleming Island, FL
- Parts Used:
- WE03X10007
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 1- 2 hours
- Tools:
- Screw drivers
Dryer drum seized
Had to pry dryer front off drum because buttons had caught between glide and felt causing excessive heat that melted the glide to the felt. Removed old felt from dryer front and replaced glide then reassembled machine. Took longer overall time because I did not realize two glide parts were needed so repair was delayed until second glide was received.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Linda from Edna, TX
- Parts Used:
- WE12X10009
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver, Screw drivers
Drum would not turn at full speed, noisy squeak
Top control panel removed; next used screwdriver to lift up dryer top on each side( the top of dryer is attached by clips on the underside) the dryer front panel has two screws, one on each side of inside front(they are easy to reach and near the top of the inside front panel, after removing these two screws we used screwdriver again to pry off front panel as it is attached also by clips on inside of front panel. At this point there is easy access to the drum where the old belt was removed, new belt put in place; removed small panel on back of dryer to access idler pulley and attached new belt through the pulley; turned the drum a couple of times by hand to check if belt was running true on the drum; problem fixed.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Virginia from South Daytona, FL
- Parts Used:
- WE01X10141
- Difficulty Level:
- Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Wrench (Adjustable)
knob on washer broke
Had a slight problen at first getting the part that I needed. Because of not knowing the model # for the washer/ the label was still on the lid of washer but the # was completely washed off. I thought I needed the complete timer/knob. I am 80 and a neighbor showed me what the problen was. Almost all of the plastic teeth were worn off.I finally found the Model # on the original purchase bill then order the knob only. My husband (86)thought I should have soneone put the new knob on but i pulled out the old clip and the new knob slipped right on. Thanks to all of your staff that helped me. Wonderful service.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Daniel from San Marcos, CA
- Parts Used:
- 5303937183
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
noise
i folow the instructions from web page
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Randy from Lake Mary, FL
- Parts Used:
- WE12X10009
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver, Screw drivers
noisy belt
Removed top of dryer, took screws out of back of dryer, pulled drum off front of dryer, removed old belt and slid new one in place. Reattached drum to front and slid belt in place only to find it was the wrong size. Called an appliance repair man, he said happens more ften than not.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Spencer from Chicago, IL
- Parts Used:
- WE25X10001
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver, Pliers, Screw drivers, Socket set, Wrench (Adjustable), Wrench set
Stackable washer & dryer
Scared to do the work myself found this website which gave me basic instructions and access to parts needed. Ordered and made an error called and CS took care of me right away. Fast friendly and will buy from them again. Great service great parts and great people!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Glenn from Aberdeen, MD
- Parts Used:
- WH01X10060
- Difficulty Level:
- Very Difficult
- Total Repair Time:
- More than 2 hours
- Tools:
- Nutdriver, Pliers, Screw drivers, Socket set, Wrench (Adjustable), Wrench set
Dryer would not start.
Checked all thermostats, they were good. Circuit was getting 220 vac. Eventually found fuse in the back near the heating element, same was bad. By-passed same, and when we did, the timer Popped & arched !. Not sure why. Motor protectrion fuse found to be good. Heating elements good. Fuse was the only bad part found, never figured out what caused it to blow. Appliance was taken away after purchase of new one. Problem not found or resolved by self diagnostics. Originally the exhaust duct was somewhat clogged with lint, but not severely.
Was this instruction helpful to you?
Thank you for voting!