DBB3300GA1WW General Electric Dryer - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- philip from pickens, SC
- Parts Used:
- WE03X37318
- Difficulty Level:
- Easy
- Total Repair Time:
- 1- 2 hours
- Tools:
- Nutdriver, Screw drivers, Socket set
Replaced Drum Bearing Front And Rear
Pulled the unit all apart to replace the rear drum bearing. Also replaced the front bearing. Works like brand new. Easier then I thought
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Jeff from Sammamish, WA
- Parts Used:
- WE1M654
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Could not adjust the timer sttings
The inner piece of the knob cracked so it just spun on the dryer shaft it's suppose to turn. Ordered a new knob, slipped it on and all works great again now.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Kelcy from Hammonton, NJ
- Parts Used:
- WE1M654
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Dryer Knob Broke
Pulled off old knob and snapped new one into place. Took about 5 seconds. Must be a lame design cause my dryer's less than 2 years old and the knob snapped on the inside and wouldn't turn. Easy to fix though.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Michael from Dallas, GA
- Parts Used:
- WE1M654
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
A different knob was broken.
The timer knob was sent, but the part on the dryer that was broken was a different knob. We were able to use the knob, but it was much bigger than the old knob.
I believe the diagram for the dryer showed the timer knob, but not the three other knobs.
I wish we would have received the correct knob, but the supplied knob is working for us.
I believe the diagram for the dryer showed the timer knob, but not the three other knobs.
I wish we would have received the correct knob, but the supplied knob is working for us.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Leslie from CAMILLA, GA
- Parts Used:
- WH01X10060
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
Start knob broke
Line up knob. Push on.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Mary from Enterprise, AL
- Parts Used:
- WE1M462
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
Loud noise
With the help of doityourself guy on the internet
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Gary from CHRISMAN, IL
- Parts Used:
- WE14X215
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Pliers, Screw drivers, Wrench set
No flame. Igniter came on but no gas.
Opened up dryer for access to all components and tested. All checked good. Put back together and tested and igniter came on but no flame. Purchased two new coils and tested again. No flame. Purchased complete valve assembly and replaced old one. Tested again and viola, success! TY PartSelect for exact replacement part.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Norm from Tahuya, WA
- Parts Used:
- WE1M654
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Timer knob on dryer was stripped (plastic was cracked.)
Pulled old knob off. Used visegrips to turn selector and when new knob arrived. Took off visegrips - pushed on new knob. Bingo! I'm a genius.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- James from INDIAN SPGS, AL
- Parts Used:
- WE1M654
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Pliers, Screw drivers
Timer knob and shaft had stripped
Replaced switch by taking out top 3 screws in back of control panel. Hold new switch in one hand and took out wire(female discount) one by one as they matched old switch. Put back in holding slot, screwed back together, DONE. If I had someone help it wouldn't have taken 10 minutes
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- William from Deerfield, IL
- Parts Used:
- WE14X215
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers, Wrench set
No heat from dryer. Diagnosed by others as the Gas Valve
Watched tecnician (I paid) as he diagnosed the problem. Four screws take of the top and front. Clothes drum slides out. Access to valve is good. Valve attaches to feed via compression fitting. Male end of fitting on unit is moved to new unit via allen wrench. Drive belt is re attached around drum and over idler easily. Part cost $90.00 shipp0ed to me. Technician asked $375.00 for this repair. Access the parts via placing the model number on Google Search.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Shirley from ASHEBORO, NC
- Parts Used:
- WE1M654
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
The Knob broke.
Just put the new knob on.
Was this instruction helpful to you?
Thank you for voting!
Part Didn't Work
I have ordered this part twice from different providers. This time there were more connections than on the older one. Still haven't gotten the dryer running.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Sandra from Brazil, IN
- Parts Used:
- WE25X217
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Wrench (Adjustable)
I had to convert from natural gas to liquid propane
My son is an engineer and repairs washers and dryers for a large commercial laundry company on a daily basis. He installed my part easily and had me up and running in no time.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Kaye from Boones Mill, VA
- Parts Used:
- WE1M654
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
This is the 2nd replacement timer knob
So simple....just put it on! Sure beats paying a $65 service charge (which we did the 1st time). Have a feeling that I'll be ordering another one.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- James from Troy, OH
- Parts Used:
- WE1M654
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Timer knob hole split
I ordered a new knob. The new knob was not broken, so it all worked out great.
Was this instruction helpful to you?
Thank you for voting!