DPXH46EA0WW General Electric Dryer - Instructions

Watch the videos for replacing the belt. The one by Kenmore is the most accurate even though it isn't GE -- the mechanisms are the same. Here is the link to the one I found most helpful: https://www.youtube.com/watch?v=G2wTmfurT5o

First: You don't need to pull the washer/dryer out at all. Leave it in place. You can put the belt around the drive shaft and get the tension pully in place by feel and inspect your work with a flasklight,

Second: There is absolutely no reason to spend $70 on a rubber belt. Other places sell it as cheaply as 10 dollars. Shop around -- the actual part is not at all impressive and should not be priced this high.

took the top off, then the front,there 2 screws that hold the front on. there's a yellow thing on the front took that off, it is held on with one screw. on the back of the dryer on the bottom is a metal plate take that off, to get to the belt take that off. then there' 3 screws in the drum, take them off ,then you can slid the drum out. then take 2 screws off the bearing bracket, that's it. easy

*****I HIGHLY RECOMMEND buying both bottom felt and top felt with glides and replacing them as a pair. Do it now!!****

First I removed the screws on the top of the control panel and lifted the control panel free. Next I pried the top cover off the drier. Reaching down inside the drier, I removed 2 screws holding the front panel in place (one on each side of the drum, screw heads are INSIDE the appliance) Then the front panel popped off toward the front, leaving the drum dangling inside the cabinet. I removed the old top felt and glides one piece) which had nothing left to them. I used a rag soaked with Acetone and a putty knife to remove the old adhesive and clean the mating surface. Following the supplied instructions (that came with the part) I glued the new piece in place. I reassembled the dryer and tested it out - I recommend giving all internal air ducts a good vacuuming while the dryer is apart - and everything seemed OK for a week. Then another article of clothing fell prey to the dryer, becoming lodged between the drum and front panel again. I suspect the culprit is the space BELOW the drum where the bottom felt is worn much more than the brand new felt just installed. I HIGHLY RECOMMEND buying both bottom felt and top felt with glides and replacing them as a pair.

Hardest part was getting the top off which ended up being quite easy, once I knew how. At the front of dryer, between the top and the cabinet, there are two spring clips that hold the top to the bottom. I could feel them with the putty knife but wasn't sure how to release them. Push on them with the blade of the stiff putty knife ... push hard and they will release. When the top was off I could see the screws that held the front. I unscrewed those, had easy access to the front glide that needed to be replaced. Pulled the old one off, followed the directions to glue the new one on, gave it about an hour to dry, reassembled and away we went. No more snagging.

Take the top off and front off and disconnect the belt and lift the drum out and there it is . Easy and alot cheaper then new dryer and works like new .

I like to fix , i have time and i just give me the chance to try , and i did it , i wish to pay less for the parts , but was a good feeling when the problem fixed

It took about 20 minutes, first I popped the top off using a flat screwdriver in my leatherman and removed the wires on the door switch then two screws holding the front on, and then I removed the drum which took a little longer because the belt tensioner was difficult to release because of limited space. Removed old bearing (ball and socket) and replaced with new one. I then reassembled in reverse order. Working great. . .

Squeaking was coming from the back of the drum, not the glides. The hardest part was trying to figure out how to pull the drum out. With a little extra tug, the back pin of the drum lifted out of the socket. That was the cause of the sqeak. Just cleaned it up and added some grease and good as new. I noticed the front glides were worn and replaced it.

Lifted top and removed front panel and cleaned old glue off. Put new glue on put seal used spring loaded cloth pins to hold till glue dried

This was done to a washer/dryer that is in a closet and was worked on in place and not removed so it was all done through the front. Its a good idea to vacuum the inside out before putting it all back together. 1.Remove all of the screws that hold down the top of the dryer and remove top. 2. Remove the front slanted panel below the controls then Remove the two small black screws holding the plastic inserts on the left and right sides of the controls panel plus the two silver screws that will allow it to drop so that you can access the tabs that hold the front section on. 3. Remove screws holding the front section with the door on. The last two will be tabs at bottom that were hidden by control panel. Unplug connector and remove front. 4. Note how belt is positioned around motor and tensioner before removing belt.(just push tensioner until belt is loose enough to slide off of drum to remove belt). 5.Slide out drum and remove old bearing and replace with new one. Be especially careful tightening the three screws that attach the bearing as they are easy to strip. 6. To remove the bushing at the back of the dryer you will remove the two screws. but you will need to hold the clip on the back of the dryer or it will drop when the screws are removed. When re-installing MAKE SURE not to lose your ball bearing that the drum bearing will rest against. I used a strong small magnet to hold the ball bearing against the back of the nylon cradle bushing so I wouldn't lose it when re-installing the bushing and it worked great. Once the nylon bushing was back in place I lubed it thoroughly and put everything back in reverse order. I usually would not fill out one of these do-it-yourself forms but the instructions that are already listed with this part are completely different from what I encountered up to the actual bearing and bushing replacement. Hope this helps.

put new knob on dryer and then dried the clothes

I Replased a belt and germetic lower and uper belt

Since the old knob was on the floor, all I did was push the new one on.

I ordered the rear bearing kit from the local supplier here in Marsh Harbour, Abaco the Bahamas. Delivery for the kit was 3 to 4 weeks from my local supplier.NOT PARTSELECT.
While waiting I found this site and after reading the VERY helpful instructions from your customers, I realised that I would probably need additional parts, top and bottom front felt seals, maybe a new drive belt.
I ordered these online and had the parts deliverd to a friends address in West Palm Beach Florida. The parts arrived in about 2 days. My wife was already there and brought the parts back.

Installation was very straight forward. Read the other installation reports and you will not have a problem.
The only thing I can add is, DO NOT LOOSE THE SMALL BALL BEARING. I did and it took me about an hour to find it.
My suggestion is to do a dry run installation of the bracket WITH OUT the small ball bearing. Tape the backing plate?that keeps the ball breaing inplace to the outside of the back panel with duct tape so that the screw hole will line up. Once this is done put some grease (Supplied with the kit) in the hole on the nylon bracket and attach with the two screws, do not over tighten. Grease up the area where the rear bearing shaft support will sit.

Installation of the rear bearing shaft support was straight forward. This is on the dryer drum. Extra hands are must for this.

I was very pleased with Partselct.
Dryer works like new.

Removed the Drum and replaced the part....