DBSR453EB2CC General Electric Dryer - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Rich from Redondo Beach, CA
- Parts Used:
- WE03X37318
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
drum wore down plastic
pulled off the top, pulled off the front then replaced the plastic that was supporting the front side of the drum. fairly easy to replace although the little plastic 'slides' (you need 4 of them)
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Kelly from Hendersonville, TN
- Parts Used:
- WE03X37318
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
Loud squeaking noise
Repair was VERY easy - 4 screws total! Used google to find a video online that showed the steps.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Bruce from Fort Mill, SC
- Parts Used:
- WE4M519
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
Dryer would start when you closed the door during a cycle
All is necessary is remove 3 philip screws, remove the switch knob, lift a tab on the switch, rotate the switch counterclockwise and it was out. Pull wires off switch and immediately put them on the corresponding terminals of the new switch before reversing the above steps. Simple!!!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Ruben from Odessa, TX
- Parts Used:
- WE4M519
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
dryer wouldn't turn off
Started out by unplugging appliance then pulled off knob, removed 4 screws that held cover in place, removed wires from switch, rotated switch to remove. reversed steps to replace.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- GUY from BEDFORD HILLS, NY
- Parts Used:
- WE03X37318
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
Drum slide wore - damaged drum bearing
r/r parts unit runs great
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Laurie from Lawrenceville, GA
- Parts Used:
- WE05X20431, WE03X37318
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers, Wrench (Adjustable)
Very Loud Noise.
Took the front & top off the dryer. Saw that the slides were missing or broken. Got the parts and put it back together. Works great.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- mike from swarthmore, PA
- Parts Used:
- WE4M519
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Pliers, Screw drivers
dryer would not turn on
Verified start switch was defective by jumping around switch to confirm the unit operated. replaced the switch.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Richard from Williston, VT
- Parts Used:
- WE03X37318
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
Dryer squeaks and squeals while running
Took the top of the dryer off by removing two philips screws in front. Removed two screws holding the front of the dryer on. Pulled the front out enough to reveal the worn drum slides. Replaced them. Reassembled.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Julie from Sterling Heights, MI
- Parts Used:
- WE03X37318
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
worn dryer drum slides
i first popped off the top of te dryer after removing the two screws in frotn when you open the door. I then removed the two screws holding the front together. after tilting the front out i was able to place the slides in without having to pull of the front entirely.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- David from santa maria, CA
- Parts Used:
- WE03X37318
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
squeaking
snap in snap out
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Jeremy from Wexford, PA
- Parts Used:
- WE03X37318
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
Loud squeaking sound from dryer drum.
Initially purchased just the plastic slides, but when I opened the dryer I found the top drum bearing was smashed and the plastic was basically gone in a whole section, so I then ended up ordering the bearing as well. If you hear the loud squeaking, just buy the top drum bearing and the 4 slides (two white and two dark green). It is an easy repair and the squeaking sound is gone.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Karen from Fort Irwin, CA
- Parts Used:
- WE4M519
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver
The Dryer Start Switch
Imagine that!! Move 3000 miles from home to home and after 90 days in storage, we finally get our things. First the washer, then the dryer. Test, no water, okay...Open valves. It's like magic. Hmmm. Plug the dryer in. No sound, not a peep. Turn the start switch one more time, crack-crack, the knob falls in my hand. Ordered the part and got in 2 days. A few star bolts to remove, unplug 3 wires and presto, it works like magic. Thanks!!!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Wayne from Fort Washington, PA
- Parts Used:
- WE03X37318
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Squeeky Noise When Dryer Was Running
First I removed the 2 screws that hold the lid down. Then I pulled the lid off. Then I removed the 2 screws that hold the front of the dryer in place. Then I lifted the drum a little and pulled the front cabinet out a little so I could see the drum slides. I removed the bad drum slides and installed the new ones. I then put everything back together and turned on the dryer. The squeeky noise was gone.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Alfred from Euless, TX
- Parts Used:
- WE4M519
- Difficulty Level:
- Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
The dryer stopped working.
I pulled the panel off of the dryer, screwed the part back on the correct wires, replaced the panel.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Robert from Big Rapids, MI
- Parts Used:
- WE03X37318
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
bearing and slides worn out
took off top of dryer, took out 2 screws so front of dryer could be removed, replaced bearing,slides and felt seal
Was this instruction helpful to you?
Thank you for voting!