DBB3300GA1AA General Electric Dryer - Instructions

Followed the Part Select video instructions which made the repair really easy!! Thanks for a job well done! ALSO.. the drum wobble was not caused by worn slides and felt. There are three screws holding the drum axle flange. Two of them fell out leaving the drum to flop about as it rotated. So we scavenged some screws from elsewhere on the dryer and problem solved. Once again.. thanks to Part Select for great instructional videos and great customer service ordering parts.

Dryer would turn on when you pushed the "on" button, but as soon as you let go, it would turn off. Found the plastic door switch cracked (from slamming door closed). Unplugged the dryer. Unscrewed the two screws inside the top of the door to unfasten the top panel. Took the top panel off. Then unscrewed the two screws on the side to unlatch the front panel. Used plyers to take the 3 wires off the switch and slid the switch through the front of the door. Juat remember where the wires go. Then inserted new switch and connected the wires. Vacuumed out the dryer and reassembled. It took about 20 minutes and was easy! If I can do it, you can!!!

To get inside the dryer in this model is extreemly difficult. I had to remove the side panel. In order to do this I needed to take off the screws on the back cover side where I needed to replace the cord. Then I needed to remove the screws to take off the top cover, front door, rear panel, trim switch, and end cap. I also had to remove the front door. After that I could tak off the side panel and change the cord.

It took a while to diagnose the problem. I finally figured out it was the door switch by pushing it with my finger with the dryer door open and starting the dryer. It would run like that, but the switch was not being pressed in enough by the door. I ordered the switch and I should have been able to replace in about 15 min. But the old switch broke while I was removing it and it fell back inside the unit. So I had to remove the top and the front panel to access the door switch. That's why it took so long. If that had not happened it would have been a much simpler repair.

followed instructions that came with kit. The problem was the instructions were not very clear with regard to the "type" of burner. the "A" type with the slot is explained but the "B" without the slot wasen't clearly explained. Even that wasen't too bad (I had to re-do that part), But you need to be 20 years old to see the damned print. I had to use my reading glasses AND a magnifying glass to read them. Also with the "B" type burner, which I have, you simply install the limiter part and you don't need (can't) adjust it.

Removing the old door was the problem as the old screws were rusty. Then, because we are not very spatially adept, we had trouble putting the door back together with correct hinge alignment. This should have taken about an hour and the part was perfect. The dryer, which we were going to throw away, looks and works perfectly! Parts Select offers great, timely service.

I removed the top of the dryer and saw that the top two drum slides where gone and the drum bearing itself was damaged I Temporally placed the parts on the drum bearing until I got the new one, that stopped the squeaking noise. All I needed to do was place the part with the hole on the little hook and then sled the other part in its slot.

Opened the door and removed 2 screws from inside/top of door. Removed top and then removed 2 screws from back of front panel. Lifted drum slightly to remove front panel and attached new slides.

Replaced drum bearing part and white slides.The problem was that it was not the drum slide support. It appears to be the the drum rear bearing of whch I am now ordering. The bearing replacement is a little more difficult, but I have taken this on as a challenge

TOO EASY to repair. WORKS GREAT>

After some research on the internet, I deduced the squeaking sound in our dryer was due to defective drum glides. I ordered a set of four of the white type, knowing only our model requires four glides, but not knowing there are two types for two locations. After disassembling the dryer I realized I needed more parts - two green slides and a new top bearing assembly. The dryer drum had eaten thru glides and into the plastic assembly. That was the reason for the squeaking noise - metal sliding against hard plastic. I ordered the additional parts directly from the manufacturer to ensure I got it right. After all the parts arrived, the repair was easy and took less than 30 minutes. I actually had my 17 year-old daughter do the work to teach her some skills. I just instructed her and stepped in on assembling the top that was just a bit tricky to put back on. Problem fixed.

remove front and top cannover's from dryer.remove plastic inside bearing housing and plastic bearing slides replace worn out bearing slides with new ones. needed 4 bearings direction suggested only two....