DPSB650EC0CC General Electric Dryer - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- rodney from VANCEBORO, NC
- Parts Used:
- WE03X29897
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers
belt broke on dryer
good replacement procedure on you tube.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Scott from Poughkeepsie, NY
- Parts Used:
- WE03X29897
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers
Dryer Not Starting
First I replaced the timer, but dryer still did not start. took apart dryer, jumper out door and componet near motor to see what problem was and to be able to run dryer while opened up. Actually motor had seized up just enough to not allow motor to start rotating. Lubricated motor shaft and rotated motor for oil to work its way in. Tried starting again and motor started. Buttoned dryer back up and reconnected wires to appropriate places and started dryer again and again.Worked for 4 loads of laundry and still working for 3 loads on Wednesday. Working fine
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Barry from WARRIOR, AL
- Parts Used:
- WE18X25100
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
Purchased a used dryer & lint filter had holes due to rust
On my GE Dryer the lint filter is located inside the door at the bottom. The filter can just be pulled out by hand & a new one pushed into place
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Kevin from GALES FERRY, CT
- Parts Used:
- WE14X25080
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Broken piece
Snap out the broken part. Snap in the new part. Use caution with the wires, but don’t have to disconnect them.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Carol from Simpsonville, SC
- Parts Used:
- WE03X37317
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Rubbing noise while dryer was running
Removed too of dryer and placed the parts on. Runs like a brand new one. Thanks so much!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Thomas from Wake Forest, NC
- Parts Used:
- WE18X25100
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
old screen was not sealing properly
Replaced new screen in place of old one.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Patrick from Albuquerque, NM
- Parts Used:
- WE03X37317
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
Dryer was making a loud squealing noise.
I replaced the dryer bearing ( a plastic part) and all of the slides on the bearing. It now operates like new.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- John from Colonie, NY
- Parts Used:
- WE09X27634, WE3M26, WE03X37317, WE03X37318
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
noisey
removed the front panel. Removed old bearing, felt and slides. Reversed operation. No problem
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Adrian from Rutland, VT
- Parts Used:
- WE09X27634, WE03X37317, WE03X37318
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
not drying clothes, felt seal hanging in the dryer
Took dryer apart replaced felt seal and the four drum slides put it back together works better now than when it was new!!!!!!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- tim from NEW PRT RCHY, FL
- Parts Used:
- WE03X29897
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 1- 2 hours
- Tools:
- Pliers, Screw drivers
evidently the pulley spring on video was very very very weak
the pulley spring took so much pressure to hold it down it took 3 men and a boy to hold it and place it in position to to get the belt on. Also there is not enough room to get your arms and hands in without getting some small cuts.Ultimately I removed the screws in the back of the dryer and spread the side of the dryer out to gain proper access. It was an easy repair if the spring would not have been so strong.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Carol from Bristolville, OH
- Parts Used:
- WE3M26
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
Screeching noise and black burn marks
I read the repairs that others had posted and how they did it. It was really easy. My only complaint is that I didn't know that I needed the slides that attached to the bearing and couldn't find them on the repair list. My dryer had a spot for 4 of them and only 1 was left. Otherwise, being a female, I felt great to be able to fix it myself! Thanks!
Let me also say, I only have one good working arm/hand.
Let me also say, I only have one good working arm/hand.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Clarke from Grapevine, TX
- Parts Used:
- WE03X37317
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
Loud squeek when dryer was running
Take out the two screws holding the top on with the door open remove top and remove two small screws in top front corners. I replaced the 4 slides and the drum bearing without the new felt, do not do this it continued to squeek after it ran the first few times when i got the new felt a week later i installed it in ten minuites and the noise is gone. I think it cost around sixty dollars and my dryer is back in action. Make sure that you clean all of the lint out of the inside of your dryer I had alot of build up near the chute for the lint trap.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- robert from woodstock, GA
- Parts Used:
- WE3M26, WE03X37318
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
Squeaking noise
Dryer was making a horrible noise. When I took it apart I noticed that the from side dryer bearing was ruined. Ordered the part with the slide bars and replaced...Works great...
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Patrick from Madisonville, LA
- Parts Used:
- WE3M26, WE03X37318
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
Front dryer drum bearing wore out
Our gas GE "Eterna" King Sized capacity dryer started squeaking one day. I was suprised since the dryer was only a few years old, but assumed some grit had invaded and worn a bearing in the belt tensioner. My wife and I have three kids, so we use the dryer daily. The sound got louder quickly and finally it was so loud I had do something. After unplugging the appliance I took the top off the dryer (two screws in the top of the door jam) and the front off (two screws at the top of each corner) and in doing so saw that the drum bearing, which is just a round plastic
"shelf" on which the tumbler drum rides, suspended over the door, was worn through. There were four little "slides" on the bearing surface, and all but one was worn down to dust. I ordered the replacement bearing and slides (two white, I didn't know I also needed two green and have since bought them too) from Part Select and they arrived in about three days. In the meantime I re-assembled the dryer easily and we did use it once or twice, shrieking. When the parts came in I installed them in about 20 minutes, screwing the new bearing onto the rear surface of the front panel, right over the opening for the dryer door. The dryer has worked perfectly since. I used one Phillips head screwdriver for the whole job and paid about $50.00 for the parts. I work in an office and I travel, and when I was a kid I fixed my own cars and stuff, but I'm no appliance repairma! Nevertheless, this was easy! I assume I saved at least $100. The dryer works perfectly and more importantly, it's quiet again!
"shelf" on which the tumbler drum rides, suspended over the door, was worn through. There were four little "slides" on the bearing surface, and all but one was worn down to dust. I ordered the replacement bearing and slides (two white, I didn't know I also needed two green and have since bought them too) from Part Select and they arrived in about three days. In the meantime I re-assembled the dryer easily and we did use it once or twice, shrieking. When the parts came in I installed them in about 20 minutes, screwing the new bearing onto the rear surface of the front panel, right over the opening for the dryer door. The dryer has worked perfectly since. I used one Phillips head screwdriver for the whole job and paid about $50.00 for the parts. I work in an office and I travel, and when I was a kid I fixed my own cars and stuff, but I'm no appliance repairma! Nevertheless, this was easy! I assume I saved at least $100. The dryer works perfectly and more importantly, it's quiet again!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Gary from Chesnee, SC
- Parts Used:
- WE3M26
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
squeeking
Looked at the diagram on your web site and replaced part
Was this instruction helpful to you?
Thank you for voting!