DBL333EA1WW General Electric Dryer - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Spencer from Chicago, IL
- Parts Used:
- WE25X10001
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver, Pliers, Screw drivers, Socket set, Wrench (Adjustable), Wrench set
Stackable washer & dryer
Scared to do the work myself found this website which gave me basic instructions and access to parts needed. Ordered and made an error called and CS took care of me right away. Fast friendly and will buy from them again. Great service great parts and great people!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Myron from Blairsville, GA
- Parts Used:
- WE4X881
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
broken post on switch
removed 4 scewws deom case snapped out switch placed the new one attached two wires re attached with the 4 screws
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Barbara from Upper Marlboro, MD
- Parts Used:
- WH1X2721
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Broken dryer selector knob
I opened the box which contained the new selector knob. Placed it on my dryer and immediately turned the knob to start the dryer. Easy steps to follow the video supplied when i ordered the part. I am greatful you responded to my order within 3 days. Thanks
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- JEAN from POPLAR GROVE, AR
- Parts Used:
- WH1X2721
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
selector knob was striped out
Just took the old knob off and put the new knob on. It was a snap. Thanks you very much
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- KAREN from CHEVY CHASE, MD
- Parts Used:
- WH1X2721
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Worn out selector knobs
Took off the broken ones and pushed on the new ones. Simple, simple
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Jesse from Chesapeake, VA
- Parts Used:
- WH1X2721
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Worn out dryer knob
I just pulled the old part out using no tools with minimum pressure and pushed the new dryer knob in with no problems at all within approximately 10 seconds.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- June from Port Charlotte, FL
- Parts Used:
- WH1X2721
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Start knob broke
It was only a matter of putting a new knob in place of the broken one. No tools required.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Richard from Bakersfield, CA
- Parts Used:
- WH1X2721
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Pliers
Dryer Start knob broken inside of stem.
Knob stem was split, leaving the metal bushing on the dryer's Start switch. Used pliers to remove metal collet. Aligned new knob to switch, and firmly pushed replacement part into place. Tested results and found it to be satisfactory.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Joel from Stockton, CA
- Parts Used:
- WE1X1263
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Broken timer knob
Knob fit perfect. Simple pull off and put new one on.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- KENDALL from COCOA, FL
- Parts Used:
- WE4X881
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Inoperative Switch
Remove & rplace switch
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Jeanne from Marblehead, MA
- Parts Used:
- WE1X1263
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
The time knob had broken and come off
Our repair was super easy. All we had to do was line the new Timer Knob up with the knob on the dryer and slip it on. Thank you!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Peter from Mercerville, NJ
- Parts Used:
- WH1X2721
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Plastics broke on inside of "Start" knob
Pushed new knob on starter shaft.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- GARY from HALEYVILLE, AL
- Parts Used:
- WE3X70
- Difficulty Level:
- Difficult
- Total Repair Time:
- 1- 2 hours
- Tools:
- Screw drivers, Wrench (Adjustable)
Lack of grease caused bearing to go out
I took the top and front off the dryer. I then took the screws out of the drum and removed the drum. I then took the old bearing out and put the new one in.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- David from Etna, ME
- Parts Used:
- WE12X10009, WE25X10001
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 1- 2 hours
- Tools:
- Screw drivers, Wrench set
bearing saddle was damaged and distorted
Depending on the condition of the bearing there are two methods described here to change the bearing, the first (and easiest) is if the bearing saddle was not damaged to the point of not allowing the bearing to lift out of it and the second is for when the saddle is damaged.
There are a few items common to both methods so I will start with them and with the belt release.
Parts Needed
Bearing and Shaft kit. Do not bother replacing just bearing or just shaft, do the kit as it is the bearing/shaft and saddle and comes with new ball bearing and grease.
Belt. if going through all this trouble replace the belt while there.
Tools needed:
8mm open/box wrench
good philips head screwdriver
a stubby philips screwdriver
putty knife or wide flat screwdriver
some duct tape
ACCESS
First, unplug the power to the unit and shut the gas off. You'll be working around the motor and burner so this is needed.
Then using the putty knife or flat screwdriver remove the top panel by depressing the latches in the horizontal seam on the front side approx 2" in from each corner.
remove the panel and set it out of the way.
Now unhook the door sensor wires and mark or store them in a manner so you will remember which side of the switch they plug into.
On each corner approx 6" down there is a philips screw, remove these and tilt the front panel forward (to clear the drum and duct seals) then lift upwards to remove the door panel.
Set this out of the way too.
REMOVE BELT FROM MOTOR
The motor pulley and tensioner are hard to see but can be done blind just by feel, they are on the lower right front side of the unit. Reach in on each side of the motor and with left hand push the tensioner towards the right side while with right hand pulling down on the tensioner spring (its a weak spring) to release it from the metal tab on bottom.
Once this is down the tensioner will move to the left and the belt can be removed from the drive puller easily.
At this point you can slide the belt forward and remove it and slide new belt on if you are only doing a belt replace.
Install procedures will be listed below.
REMOVING DRUM
FOR NON-DAMAGED SADDLE
If the saddle is not damaged you can now jerk up (not too much force) on the rear of the drum and this will pop the shaft bearing end out of the saddle. Then carefully slide the drum forward through the cabinet to a palce you can access it easy.
Remove the shaft and bearing from the drum by removing the three phillips screws whose heads are inside the drum.
Now remove the saddle from the cabinet by removing the 2 bolts (8mm head) that go trough the rear, there is a ball bearing in the saddle that may be useful to save in case you drop the new one and there is a screwplate on exterior rear that will fall when you remove the final bolt.
FOR DAMAGED SADDLE
If the saddle is damaged (distorted) the procedure is a bit different and quite a bit harder, but not awful bad. It adds about 20 to 60 minutes extra (depends on how the screws come out) to the whole job.
First remove the drum from the shaft by unscrewing the three philips head screws from inside the drum and, like in prior method, carefully pull the drum through the front of the cabinet and set it aside.
Then to remove the saddle you may be able to remove the two 8mm head bolts by flexing the plate to the side and loosening each bolt a bit while alternating. However I had to actually move the burner ducts a bit to get at mine as I could not turn the left side bolt.
This is where the stubby screwdriver is needed, there are 4 philips screws whose heads are hidden by the seals on the ducts, by folding the seal back a bit you can access them. I was able to just do the three at the top, left, and lower left and slide the duct a bit to allow wrench access to the bolt. I did not have to remove the lowest screw myself but you may need to.
Always make sure to not bend the tin too much and this will hurt heat movement through the system.
Once you have the saddle removed, rememberi
There are a few items common to both methods so I will start with them and with the belt release.
Parts Needed
Bearing and Shaft kit. Do not bother replacing just bearing or just shaft, do the kit as it is the bearing/shaft and saddle and comes with new ball bearing and grease.
Belt. if going through all this trouble replace the belt while there.
Tools needed:
8mm open/box wrench
good philips head screwdriver
a stubby philips screwdriver
putty knife or wide flat screwdriver
some duct tape
ACCESS
First, unplug the power to the unit and shut the gas off. You'll be working around the motor and burner so this is needed.
Then using the putty knife or flat screwdriver remove the top panel by depressing the latches in the horizontal seam on the front side approx 2" in from each corner.
remove the panel and set it out of the way.
Now unhook the door sensor wires and mark or store them in a manner so you will remember which side of the switch they plug into.
On each corner approx 6" down there is a philips screw, remove these and tilt the front panel forward (to clear the drum and duct seals) then lift upwards to remove the door panel.
Set this out of the way too.
REMOVE BELT FROM MOTOR
The motor pulley and tensioner are hard to see but can be done blind just by feel, they are on the lower right front side of the unit. Reach in on each side of the motor and with left hand push the tensioner towards the right side while with right hand pulling down on the tensioner spring (its a weak spring) to release it from the metal tab on bottom.
Once this is down the tensioner will move to the left and the belt can be removed from the drive puller easily.
At this point you can slide the belt forward and remove it and slide new belt on if you are only doing a belt replace.
Install procedures will be listed below.
REMOVING DRUM
FOR NON-DAMAGED SADDLE
If the saddle is not damaged you can now jerk up (not too much force) on the rear of the drum and this will pop the shaft bearing end out of the saddle. Then carefully slide the drum forward through the cabinet to a palce you can access it easy.
Remove the shaft and bearing from the drum by removing the three phillips screws whose heads are inside the drum.
Now remove the saddle from the cabinet by removing the 2 bolts (8mm head) that go trough the rear, there is a ball bearing in the saddle that may be useful to save in case you drop the new one and there is a screwplate on exterior rear that will fall when you remove the final bolt.
FOR DAMAGED SADDLE
If the saddle is damaged (distorted) the procedure is a bit different and quite a bit harder, but not awful bad. It adds about 20 to 60 minutes extra (depends on how the screws come out) to the whole job.
First remove the drum from the shaft by unscrewing the three philips head screws from inside the drum and, like in prior method, carefully pull the drum through the front of the cabinet and set it aside.
Then to remove the saddle you may be able to remove the two 8mm head bolts by flexing the plate to the side and loosening each bolt a bit while alternating. However I had to actually move the burner ducts a bit to get at mine as I could not turn the left side bolt.
This is where the stubby screwdriver is needed, there are 4 philips screws whose heads are hidden by the seals on the ducts, by folding the seal back a bit you can access them. I was able to just do the three at the top, left, and lower left and slide the duct a bit to allow wrench access to the bolt. I did not have to remove the lowest screw myself but you may need to.
Always make sure to not bend the tin too much and this will hurt heat movement through the system.
Once you have the saddle removed, rememberi
Was this instruction helpful to you?
Thank you for voting!