DCSR473EV0WW General Electric Dryer - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
First, wouldn't stop running, then wouldn't start.
I suspected and removed the timer to check it and found the timer knob had a crack in it and realized I did not know where it was pointing to. Checking the selector knob also showed a crack which prevented the dryer from starting.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Brian from Richmond, VA
- Parts Used:
- WE4M415
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- More than 2 hours
- Tools:
- Nutdriver, Screw drivers
Dryer would not turn on
It took a while to diagnose the problem. I finally figured out it was the door switch by pushing it with my finger with the dryer door open and starting the dryer. It would run like that, but the switch was not being pressed in enough by the door. I ordered the switch and I should have been able to replace in about 15 min. But the old switch broke while I was removing it and it fell back inside the unit. So I had to remove the top and the front panel to access the door switch. That's why it took so long. If that had not happened it would have been a much simpler repair.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- William from Huntington Beach, CA
- Parts Used:
- WE03X37318
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
Dryer squeaking/squealing sound
After some research on the internet, I deduced the squeaking sound in our dryer was due to defective drum glides. I ordered a set of four of the white type, knowing only our model requires four glides, but not knowing there are two types for two locations. After disassembling the dryer I realized I needed more parts - two green slides and a new top bearing assembly. The dryer drum had eaten thru glides and into the plastic assembly. That was the reason for the squeaking noise - metal sliding against hard plastic. I ordered the additional parts directly from the manufacturer to ensure I got it right. After all the parts arrived, the repair was easy and took less than 30 minutes. I actually had my 17 year-old daughter do the work to teach her some skills. I just instructed her and stepped in on assembling the top that was just a bit tricky to put back on. Problem fixed.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- RAMCHANDAR from BRISTOW, VA
- Parts Used:
- WE03X37318
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
noisey
TOO EASY to repair. WORKS GREAT>
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Doyle from Edisto Beach, SC
- Parts Used:
- WE1X1263
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
bad timer knob
just pushed it on . This was one of the most pleasant internet ordering experiences I have ever had. Glad I found you. Thanks Doyle Weeks
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Barbara from Upper Marlboro, MD
- Parts Used:
- WH1X2721
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Broken dryer selector knob
I opened the box which contained the new selector knob. Placed it on my dryer and immediately turned the knob to start the dryer. Easy steps to follow the video supplied when i ordered the part. I am greatful you responded to my order within 3 days. Thanks
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- JEAN from POPLAR GROVE, AR
- Parts Used:
- WH1X2721
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
selector knob was striped out
Just took the old knob off and put the new knob on. It was a snap. Thanks you very much
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- jeffrey from hertford, NC
- Parts Used:
- WE03X37318
- Difficulty Level:
- Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Loud Squealling noise from dryer
Opened the door and removed 2 screws from inside/top of door. Removed top and then removed 2 screws from back of front panel. Lifted drum slightly to remove front panel and attached new slides.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Robert from Orange, CA
- Parts Used:
- WH1X2721
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Broken knob
Simple replacement. Very easy.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Anita from Knoxville, TN
- Parts Used:
- WE1X1263
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Timer Knob - Stripped
Parts arrived and it took me less than 5 minutes to get the packaging open and install the knew timer knob. I had ordered a separate D-ring; however, one was already present in the timer knob so now I have an extra.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Rita from Cape Coral, FL
- Parts Used:
- WH1X2721
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
plastic selector knob on front of dryer cracked
new knob fit onto 'd' shaped spindle. This took about 30 seconds.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Larry from Wilmington, NC
- Parts Used:
- WE03X37318
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
High Pitch Sqeaking durng dryer operation
Replaced drum bearing part and white slides.The problem was that it was not the drum slide support. It appears to be the the drum rear bearing of whch I am now ordering. The bearing replacement is a little more difficult, but I have taken this on as a challenge
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Shauna from Bend, OR
- Parts Used:
- WE03X37318
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
High Squeaking noise
I removed the top of the dryer and saw that the top two drum slides where gone and the drum bearing itself was damaged I Temporally placed the parts on the drum bearing until I got the new one, that stopped the squeaking noise. All I needed to do was place the part with the hole on the little hook and then sled the other part in its slot.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Charlene from Winchester, KY
- Parts Used:
- WE1X1263
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Knob came off
I'm not experience to repair anything so I put the laptop on top of the washer and watch the video and it was easy
Was this instruction helpful to you?
Thank you for voting!