DVL223GB0WW General Electric Dryer - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Alonso from MONTGOMRY VLG, MD
- Parts Used:
- WE12X10009, WE13X10011
- Difficulty Level:
- Easy
- Total Repair Time:
- 1- 2 hours
- Tools:
- Screw drivers
Rear bearing was broke
I like to fix , i have time and i just give me the chance to try , and i did it , i wish to pay less for the parts , but was a good feeling when the problem fixed
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Gene from LaGrange, GA
- Parts Used:
- WE25X10001
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver
Back Drum Bearing Worn Out
It took about 20 minutes, first I popped the top off using a flat screwdriver in my leatherman and removed the wires on the door switch then two screws holding the front on, and then I removed the drum which took a little longer because the belt tensioner was difficult to release because of limited space. Removed old bearing (ball and socket) and replaced with new one. I then reassembled in reverse order. Working great. . .
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Joanne from Cecil, WI
- Parts Used:
- WE4X881
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Start knob was broken off flush with switch
I turned off the power, unscrewed the 4 screws from the top of the dryer. I then opened it and turned the switch that was in there counterclockwise exactly as utube video said to do. I then took off the two wires from the old switch. The rotary start switch fix right in where the old one was. I put the panel back together, put on the old knob and turned the power back on! It took less than 15 minutes from start to finish! If I can do it anyone can! Joanne Klinkhammer Cecil, Wisconsin
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Jonathan from Ridgefield, CT
- Parts Used:
- WE4X881
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
broken spindle which required a total switch replacement.
It took longer to vaccume the lint out of the machine than to change the part.
The part replacement is done without any tools.
My wife could have done it
The part replacement is done without any tools.
My wife could have done it
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Dwayne from lawrenceville, GA
- Parts Used:
- WE4X881
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver, Pliers, Screw drivers
Timers are made to turn clockwise and break when turned counter clockwise
We are a retirement community and when we opened March '07 the company purchased GE washer and dryers to go in our common area laundry rooms for the residents to use. Because of their age, they will often turn the knob counter clockwise and not the right diirection which breaks the device which is not good. With in 3 days of installation they had broken 2 of the new knobs.
But, the ordering was simple, the shipment was fast and the install was quick for the maintenance tech.
But, the ordering was simple, the shipment was fast and the install was quick for the maintenance tech.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Sherry from Marietta, OH
- Parts Used:
- WE4X881
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers, Socket set, Wrench set
Start switch broke
Followed the on line instructions.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Pamela from Atlanta, GA
- Parts Used:
- WE4X881
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Start switch broke off
I followed the video instructions. I did have to run to the hardware store to pick up a torx screwdriver but otherwise the instructions were perfect. I generally hire someone to do repairs, but this was too easy! I highly recommend doing this yourself as it is definitely a time and money saver. The website made ordering easy and the part arrived quickly!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- NICOLAS from LYNN, MA
- Parts Used:
- WE3X70
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers, Wrench set
Dryer making squeeky noise.
Removed the Drum and replaced the part....
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Randy from Lake Mary, FL
- Parts Used:
- WE12X10009
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver, Screw drivers
noisy belt
Removed top of dryer, took screws out of back of dryer, pulled drum off front of dryer, removed old belt and slid new one in place. Reattached drum to front and slid belt in place only to find it was the wrong size. Called an appliance repair man, he said happens more ften than not.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Mitsuhiro from Anaheim, CA
- Parts Used:
- WE04X10020
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver, Screw drivers
Dryer runs but no heat
I first checked the heating element by peeking through the peek hole in the front to see if it was turning on. The heating element turned on but gas failed to flow. Next, I checked all sensors including the fuse, they were all fine. This points to the solenoid as the cause of the issue. So I replaced the solenoids and the problem solved. I did watch the YouTube video on how to check the sensors and replace faulty parts.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Spencer from Chicago, IL
- Parts Used:
- WE25X10001
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver, Pliers, Screw drivers, Socket set, Wrench (Adjustable), Wrench set
Stackable washer & dryer
Scared to do the work myself found this website which gave me basic instructions and access to parts needed. Ordered and made an error called and CS took care of me right away. Fast friendly and will buy from them again. Great service great parts and great people!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Glenn from Aberdeen, MD
- Parts Used:
- WH01X10060
- Difficulty Level:
- Very Difficult
- Total Repair Time:
- More than 2 hours
- Tools:
- Nutdriver, Pliers, Screw drivers, Socket set, Wrench (Adjustable), Wrench set
Dryer would not start.
Checked all thermostats, they were good. Circuit was getting 220 vac. Eventually found fuse in the back near the heating element, same was bad. By-passed same, and when we did, the timer Popped & arched !. Not sure why. Motor protectrion fuse found to be good. Heating elements good. Fuse was the only bad part found, never figured out what caused it to blow. Appliance was taken away after purchase of new one. Problem not found or resolved by self diagnostics. Originally the exhaust duct was somewhat clogged with lint, but not severely.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Daniel from Maryville, TN
- Parts Used:
- WH01X10060
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Pliers
Broken knob
Used pliers to remove old clip. Installed new clip and knob. Very easy.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Dan from Fernley, NV
- Parts Used:
- WE4X881
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Pliers, Screw drivers
The switch was broken and had to use pliers to start dryer
Disconnected the power removed 4 screws from top panel. Removed 2 wires, turned switch counter clockwise. remopved switch. Replaced with new switch,connected the 2 wires, put panel back inplace,put screws back in panel,plugged dryer back in. SUPER SIMPLE Total time 5 minutes
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Sue from Norfolk, MA
- Parts Used:
- WE4X881
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver, Screw drivers
switha broke off
Removed old switch, replaced it with new
Was this instruction helpful to you?
Thank you for voting!