DBXR463GB0CC General Electric Dryer - Instructions

Followed the Part Select video instructions which made the repair really easy!! Thanks for a job well done! ALSO.. the drum wobble was not caused by worn slides and felt. There are three screws holding the drum axle flange. Two of them fell out leaving the drum to flop about as it rotated. So we scavenged some screws from elsewhere on the dryer and problem solved. Once again.. thanks to Part Select for great instructional videos and great customer service ordering parts.

This is the 2nd time we had to replace the slides. Not a big deal. Removed the top & front of the dyer and replaced the new slides. It's also a good time to vacuum out the inside while you have it apart. Be advised.... Get your tools ready. You'll be receiving your parts quickly. Couldn't believe how fast they arrived!

Easier than I thought it would be. I was hoping it was the front bearing because replacing the rear bearing looked pretty gnarly. Unplugged the dryer from the outlet. Removed two screws inside the door frame. Lifted the top off. Unscrewed the two screws holding the front on. Lifted the front panel off, careful of the wires going to the door. Popped out the old front bearing by releasing the two clips at the top. The old bearing was pretty trashed. The two grey/green slides were in tatters and one of the white ones was missing. Not too much lint inside the dryer, but the lint trap was pretty clogged. Cleaned the insides out with the shop-vac. Inserted the new slides into the new bearing an snapped it back into place, careful to make sure the light went in the hole. The felt gasket at the botton was in good shape so did not replace it. Replaced the panels screwed them back to together and it fired up smooth and quiet.

I went to replace all four of the drum slides but in the process of doing this, found out that the whole of the top support had been rubbed away! I therefore ordered a replacement top support and replaced it per the instructions in the PartSelect webpage and from the youtube demonstration and completed the repair. I had a little trouble with getting the top support installed, but by jiggling it around and persistence I was able to complete the repair. The help I received on the webpage and video were invaluable! Thank you to PartSelect and to the other users for all your help!!

followed instructions that came with kit. The problem was the instructions were not very clear with regard to the "type" of burner. the "A" type with the slot is explained but the "B" without the slot wasen't clearly explained. Even that wasen't too bad (I had to re-do that part), But you need to be 20 years old to see the damned print. I had to use my reading glasses AND a magnifying glass to read them. Also with the "B" type burner, which I have, you simply install the limiter part and you don't need (can't) adjust it.

Googled possible problem where noise was coming from. Went to Parts Select web site. Ordered felt and drum bracket. Removed screws behind control knobs and removed top of dryer. Removed two screws on front inside dryer (left/right side) this allowed me to remove front panel of dryer. Unattached wires. Drum bracket is located above door opening...pretty much snaps out, felt piece is located on bottom bracket. Felt piece was replaced and new top bracket replaced. Reattach wires, lift drum slightly to fit doo iInto place. Dryer still made noise. Noticed I did not have any drum slides! Drum slides slide into top of front bracket at 10/2 o'clock position and 11/1o'clock. Easy and very inexpensive dryer repair!! My husband was very impressed that I could take dryer apart and fix!!!

TOO EASY to repair. WORKS GREAT>

replaced the parts that had worn out

It was as easy as the repair film said it was . But after spending the money for the upper and lower baring seals I put it all back together and the motor started making a loud noise ? I took the drum and everything out and started the motor without the drum just the motor was running and the danged motor is going out now !I checked the price of a new motor its not to bad but with all of the parts I have put in this thing I could have paid part of what it would have cost for a new dryer ! I put it all back together and hope it last long enough to at least recoup some of what I have spent ,But the new parts work good !

The repair was extremely easy to do. The video was perfectly done and described everything one needed to do in very simplistic details.

I took the visegrip pliers off the d shaft and simply slid the new knob on with ease. I never doubted my abilities!

Opened the door and removed 2 screws from inside/top of door. Removed top and then removed 2 screws from back of front panel. Lifted drum slightly to remove front panel and attached new slides.

Removed 2 screws from inside door lifted top panel up,removed 1 screw attaching front panel to left side. Pulled front panel out far enough to remove and replace slider bearing.

The old knob broke off & was no longer able to turn the pin to start the dryer. I simply slid the new knob onto the pin & it worked like new.

Pulled on the two ends towards the outside edge and it popped right off. snapped the new on.The new one is stronger and Partselect shipped it to my door in 3 days.Thanks