DBXR463GB0CC General Electric Dryer - Instructions

Pulled the unit all apart to replace the rear drum bearing. Also replaced the front bearing. Works like brand new. Easier then I thought

After reading comments made by other customers, I ordered the timer and it arrived 3 days later. I used a star bit with the electric screw driver to open the top of the dryer. I removed all the dials and pulled open the top cover of the dryer. I carefully lifted the "tang" that kept the timer in place and turned the timer clockwise. I then used my cell phone camera and took picutres of all the connections so that it would be easier to reconnect the wireing to the new timer. I disconnected the wiring from the old timer and reconnected them to the new timer. I inserted the tang place in place and rotated the time timer counter clockwise. I then placed the cover back on, inserted the star screws and tighten them down. I put back all the dails and the dryer is working perfectly since. Took about 30 mins. I'm very pleased with the delivery of the timer and the ease of the installation. I will use Part Select as my sole supplier for all future repairs on my appliances. Part Select is Number 1 in my book!!!!

It was amazingly simple and I am not even a handy man by any means. The only difficult part was pulling the cable connections as they are a bit tight. I was glad that I could accomplish this task for which the repair person was demanding $120.
Most of these things are doable it's just that common folk are just too scared to even try them out. I figured rather than going out to buy a new dryer for $500 ( and if my wife had her way, $1000) I could give it a shot for $80.

This repair was the easiest that I've ever done. Removed 4 torx head screws on the back and the timer unsnapped from its holder. I unplugged one wire at a time and plugged each one to the new timer. This part came the next day after I ordered it and PartSelect was cheaper than any other supplier.

Removed that to screws for that top first and door shake top little to that front and I took two screws on that top each side and removed that front and lint trap and install the new

With my hands, a 2 yr old could of done it. But I was amazed how quickly I received the part. Thanks

I followed the very easy YouTube video and got the three tools I needed before beginning. I started with removing the parts of the dryer and that was extremely simple by following the steps in the video. Took the door off last, located the parts that need replaced that didn't require any tools at all. Then put all the parts of the dryer back on in the order I removed them. The entire process was about 25 minutes but I would say I spent more time really cleaning the dryer and lint build up than actually doing the repair. Video was super thorough and easy to follow, I've never attempted any kind of repair of an appliance and I'm extremely happy that I had the video and the parts that were recommended to fix my problem, were spot on. Saved me hundreds of dollars and time. Thank you so much!

I replaced the drum bearing slides and also the main front drum bearing. First, disconnect the electric. Then I removed the two screws inside the door that attach the top cover, removed the top cover, removed two screws that attach the front cover, lift up the front cover and pivot it to the left leaving the wiring attached, removed the front bearing assembly by pulling it out at the top and then up, installed the new front bearing ring and snap it into place, installed the drum bearing slides, reinstalled the front cover, reinstalled the top cover, and tested the drum by turning it by hand first and then under power. The whole operation took less than 15 minutes....

Pull the two scews to release the top of the cabinet. Pull the two screws to release the face of the cabinet and tilt out.
Take the old slide out and install the new ones.
Put it back together.
No more squeeks
My wife thinks I'm a genius...

Opened dryer door and removed two screws that held front of top panel on. Lifted top panel off and removed two screws that held front panel to side panels. Tipped front panel forward and replaced all four slides. Cleaned everything off and put back together. Works great again. Thanks for this site and for others that have done these repairs before and posted their stories.

Line up knob. Push on.

When we first heard the screeching i thought right away that it was the belt. we ordered a new one and after i replaced it the dryer was still just as loud. I wished i went here first. Right away i found others with the same problem, did the same repair which was just taking 2 screws out, sliding the top and front panel off(watch for the electric wire connected to the panel) and replace a couple of plastic slides. now it is better than ever.

I order the parts needed to replace the slides, the felt ,and the bearing on a Sunday afternoon. The parts arrived on Tuesday even though I used regular shipping. I followed the instructions posted by another customer. It was extremely easy and only took me about fifteen minutes. My only problem was that I needed 2 each of the front slide and the rear slide, and I unknowingly only ordered 1 of each. I order the other 2 on Tuesday via regular shipping and they arrived on Wed. AMAZING!!!!

With the help of doityourself guy on the internet

First I watched the repair video on partselect.com and that really helped. It was really easy to replace the slides. I even ordered a new top bearing, old one was busted, and replaced it. Thank you for your help.