DBXR453EA0WW General Electric Dryer - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Jack from Landenberg, PA
- Parts Used:
- WE1X1263
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver, Screw drivers
Old knob would not turn shaft and dryer would not start. Cracked in center.
Turned off breaker, rmoved back panel, removed timer, replaced knob. Put back together.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Dave from Wallingford, CT
- Parts Used:
- WE4M137
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Pliers, Screw drivers
Dryer would shut off on heat dry after a couple of minutes. I could feel the heat working. It would only continue to run on fluff/no heat
Pulled the drum an found spade clip burned on wire. Hi limit Thermostat crumbled/ broke while pulling spade clip so I trimmed back the wire, cleaned the spade clip and soldered the wire back on. Isolated the other thermostats in the system and tested for resistance. Reassembled dryer.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Cheryl from Inwood, WV
- Parts Used:
- WE03X37318
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers
Making noise while drum was turning.
Removed 2 screws to remove top. Removed 2 other screws to remove front. Removed old parts. Installed new parts. Reassemble all afetr cleaning duct work out.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Donna from Vista, CA
- Parts Used:
- WE05X20431
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Light bulb blew out inside the dryer
Screwed the light bulb into the socket (duh)
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Wagdy from Watertown, MA
- Parts Used:
- WH1X2721
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
The two dial buttons were broken on a white appliance. The dials sent were bone white.
Pull out old, insert new.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Jessica from Spanaway, WA
- Parts Used:
- WH1X2721
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Start knob on dryer broken
There really is not much to explain, the new knob was so simple to replace that my six year old could have done it. No tools were required and it took less than a minute to replace the new knob.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Roy W from Albany, OR
- Parts Used:
- WH1X2721
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
On knob was broken
Removed knob and installed the replacement.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- John from Andover, NJ
- Parts Used:
- WE1X1263
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Knob had cracked inside
Just pulled off the old knob and pushed the new one onto the switch. Done in 1 minute.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Linda from Levittown, PA
- Parts Used:
- WH1X2721
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
missing knob
the part fixed all the problems in a cinch
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- krisy from anniston, AL
- Parts Used:
- WE1X1263
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Dryer timer knob would not work
Easy! Just took the broken knob and metal ring off, and put on the new knob. took less that one minute. Works like a charm now. No service call cost either!!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Catherine from Dunmore, PA
- Parts Used:
- WH1X2721
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
dryer wouldnt start
just replaced the old knob
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- starla from Fort Cambell, KY
- Parts Used:
- WE1X1263
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Pliers
Knob was broken off ordered a new knob.
First the old knob was broken just pulled it off. made sure the metal piece was clean of all debris or junk and slide the new know on turned it to make sure it was snug and was ready to go. to easy
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Julie from Portland, OR
- Parts Used:
- WH1X2721
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
bdryer broken knob
I just put the new knob where the old one was and presto it was done. The whole process was much easier than I expected.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Linda B from Ogden, UT
- Parts Used:
- WH1X2721
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Dryer knobs were cracked and would not turn.
Before I bought the new knobs, I put nail glue inside each knob to strengthen the knobs. It lasted for about 6 mos and I would have to do it again. Needless to say I got tired of the broken knobs, so I bought new ones.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Delta from Angleton, TX
- Parts Used:
- WH1X2721
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
The old knob was cracked
Just put the new knob on the machine.
Was this instruction helpful to you?
Thank you for voting!