Models > EGD3000B0WW > Instructions

EGD3000B0WW General Electric Dryer - Instructions

Jump to:

All Instructions for the EGD3000B0WW
91 - 105 of 297
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Customer:
Thomas from Staten Island, NY
Parts Used:
WE4M189
Difficulty Level:
Easy
Total Repair Time:
15 - 30 mins
Tools:
Pliers, Screw drivers
Timer would not regulate dryer time
I was able to take off the front top panel (4 star screws) folded top panel towards me. Marked all the wires to make it easier to remember where they go on new timer. (could have just removed and replaced on new timer as wires were long enough. Pushed old timer down onto panel with screw driver to loosen (this was hardest part) once I was able to loosen and remove the new timer was easy to replace and tighten. Put wires in place. Folding top panel back into place. Closed and tightened screws. Project done!!! Saved about $200.00... GO ME!!!
3 of 8 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
David from Lawrenceville, GA
Parts Used:
WE03X37317, WE03X37318
Difficulty Level:
Really Easy
Total Repair Time:
15 - 30 mins
Tools:
Screw drivers
Squeaking and black marks on clothes.
Unplug the dryer. Remove top panel (remove two screws on the upper inside edge of the dryer door). Lift the front panel from front (tabs and slots at the back) and lift off. Remove the front panel (remove a screw from each side - top/front). Front panel sits on two feet at the bottom, tilt it forward from the top and lift it up (careful not to damage the electrical connection at the bottom left side). I found the dryer had another damaged part (plastic guide that the Slide WH and the Drum Slides connected to was badly worn). After ordering the additional part I attached the slides (white and gray) to the guide. Set the front panel back on the two feet and tilt it back into place (you'll need to slightly raise the drum back into position - easy). Replace the two screws that connect the front panel. Replace the top cover. The whole repair took less than 1/2 an hour including the time it took to vacuum out the dust. Total cost, about $35!
1 of 2 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
Corinne from Woodstock, MD
Parts Used:
WE1M654
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins
Broken timer knob
All I had to do was snap it on and was ready to go. How easy was that. Would order any other parts again.
1 of 2 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
jackie from bechtelsville, PA
Parts Used:
WE1M654
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins
knob was broke inside its self.
removed old knob, cleaned surface under knob, sprayed metal knob on dryer with wd-40, put new knob on. useing the wd-40 makes the knob turn a lot easyer.
1 of 2 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
Michael from Broussard, LA
Parts Used:
WE4M189
Difficulty Level:
Easy
Total Repair Time:
1- 2 hours
Tools:
Screw drivers
Broken Pulley Idler and Timer.
Hello,

I just want to start by saying thanks to Partselect for having such a great website. The site is easy to navigate and with the explosion views allowed 'us novice' to select the right part the first time.

With post from previous DIY'ers, help make my repair very easy and simple. I had to replace the timer and the Pulley Idler. I first removed the top, leaving the timer panel connected by wires. I then removed the belt from the drum. That step was easy since the Pulley Idler was broke. I simply slid off the drum with ease. Once the belt was off I disassembled the front panel of the dryer. With the front panel off, I used a 3ft clamp to hold the drum in place while I unscrewed the three drum screws inside. I then pulled the drum out and set to the side. The tension pulley was simple to remove and reinstall. I reversed the steps above until the I got to the installation of the timer panel. With the new timer I put them side by side. I pulled one wire at a time and replaced to the new timer. Once all wires have been transferred, I then pulled the knob off the front. I used a small and medium flat head screwdriver, the small one to pry up the keeper flap and the medium to hold it. I was able to turn the timer and release it with ease. I then inserted the new timer and replaced the knob. I finished reinstalling the dryer and tested. Works great! This all took approximately an hour.
2 of 6 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
Michael from Lumberton, NJ
Parts Used:
WE01X20419
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins
Plastic door handle broke
Snapped on new handel. Took all of 5 seconds. The hardest part was finding the part, which your website took care of....Thanks!
1 of 3 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
Gerald from Ontario, NY
Parts Used:
WE1M654
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins
Cound not set timer, knob was broken.
Silmply replaced the knob. This is the second knob I have replaced on this dryer. This time I bought two for when it happens again. Not sure if it is too much rension in the timer or too little strength in the knob, but is a design problem.
0 of 1 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
Donald from Frederick, MD
Parts Used:
WE1M654
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins
Broken Timer Knob
The fact that the knob on a 3yr old dryer broke was harder to deal with than the repair. It was lift the old knob off (it was very loose) and snugly slide the new knob on. I can get back to reading my book and my wife thinks I'm a hero win-win!
0 of 1 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
Dale from Southampton, NY
Parts Used:
WE01X20419
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins
After 12 years the handle on my GE washing machine broke.
Simply pulled off the old handle and snapped in the new one! No tools required. Took about 5 seconds!
0 of 1 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
robert from plaquemine, LA
Parts Used:
WE4M189
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins
Tools:
Screw drivers
timer would not work
Took top off ,4 screws.Took old timer out and just transferred wires to new one, very easy and worked perfect.Would probally get new knob also if ever done again.
2 of 7 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
Michael from Houghton Lake, MI
Parts Used:
WE01X20419
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins
broken door handle
just snap in replacement
0 of 1 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
Robert from Plattsmouth, NE
Parts Used:
WE03X37317, WE03X37318
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins
Tools:
Screw drivers
Load Noises when dryer was running
Unscrewed screws took off new parts and replaced with new parts and put back together. Works great now! No Noise!
0 of 1 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
Vicki from Redlands, CA
Parts Used:
WE01X20419
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins
Door handle broke off
Just popped the new door handle on.
0 of 1 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
theresa from nederland, TX
Parts Used:
WE1M654
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins
dryer knob broke
When the part came in the mail. I opened the packaging & just pushed the knob on to the metal post of the dryer. Voile that easy!
0 of 1 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
Frank from MECHANICSBURG, IL
Parts Used:
WE03X37317
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins
Tools:
Screw drivers
for about 6 months our dryer has been making a sqealing noise and kept getting worst
I took off the dryer top and saw it was the slides went on line found PartsSelect, found my dryer, ordered the parts and had them within two days and it took me about 15 minutes to fix the dryer which will add about 3-4 years more life on it. Thank You PartsSelect My wife is even happier
0 of 1 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
All Instructions for the EGD3000B0WW
91 - 105 of 297