DBXR463GB1CC General Electric Dryer - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- MICHAEL from HUNTLEY, IL
- Parts Used:
- WE4M519
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
On-Off Switch would not turn on or if it worked it wouldn't the next time
1. Unplug. 2. Remove 4 screws with hex screwdriver. 3. Remove 2 left Knobs. 4. Lean panel Forward. 5. Remove Switch by depressing clip and twisting from Slot. 6. Take off one wire at a time from old switch and replace on new switch. 7. Lean Panel forward and reinstall 4 screws. 8. Replug and turn on Dryer. AMAZING HOW SIMPLE IT WAS. THIS IS THE 3RD SWITCH IN 9 YEARS. THE FIRST TIME IT COST $45 FOR SERVICE CALL PLUS $20 FOR PART. I REPLACED 2 TIMES FOR $15 EACH TIME (Includes shipping cost of part.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Adrienne from Beaver, PA
- Parts Used:
- WH01X10060
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Pliers
Start knob broke from being turned too far
Fortunately I watched the video on how to change the knob. I may not have noticed that the metal clip part of the old knob was still attached. Once the old part was removed, the new knob slid right into place.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Marvin from Monticello, FL
- Parts Used:
- WE4M519
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Dryer "Start Switch" would not work
I Removed 5 "Star Screws" for access to the back side of operating switch panel. Removed wires from old start switch, then removed switch. Installed new start switch and wires. I re-installed access panel and star screws. Dryer was back to normal. Total time: less than 10 minutes.
I was very happy with partsselect.com. The website was VERY easy to use. I placed my order about noon and I received the start switch before 10:00 am via FedEx the next day. Thanks for your help PartsSelect!
I was very happy with partsselect.com. The website was VERY easy to use. I placed my order about noon and I received the start switch before 10:00 am via FedEx the next day. Thanks for your help PartsSelect!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Hector from Baytown, TX
- Parts Used:
- WE4M519
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Had Difficult Time Getting Dryer To Start When Turning Switch
Pop off top access panel twist switch out and reverse twist switch back in. . Very simple
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Jason from Gastonia, NC
- Parts Used:
- WE4M519
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Wrench (Adjustable)
Dryer would not start
I turned off the breaker. I took off the top four torx screws. I pulled the wires one at a time from the old switch and put them on the new switch. Secured the new switch. Replaced the torx screws. Turned on the breaker and it ran.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Tom from Hatley, WI
- Parts Used:
- WE01X20580
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Dryer handle cracked
Pulled on the two ends towards the outside edge and it popped right off. snapped the new on.The new one is stronger and Partselect shipped it to my door in 3 days.Thanks
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Jerry from Simpsonville, KY
- Parts Used:
- WE4M519
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Pliers, Screw drivers
Dryer would not shut off. If dryer door was opened while running and then door closed,dryer would restart without turning start knob.
Pulled the dryer out away from wall. UNPLUG dryer. Using Phillips screwdriver remove the 5 screws holding the metal plate behind the back splash. Remove the 2 screws holding the smaller metal plate at bottom center of the larger . From the front pull the start knob straight out remove. Grasp switch and turn clockwise and pull out switch. Hold new switch and pull wire/ terminal one at a time and install on new switch. Repeat until all wires are installed on new switch. Rotate switch to approximately two o'clock position and while pushing turn switch counter clockwise to lock switch into position. Reinstall all plates that were removed. Plug back in and reinstall knob noting "d" shaped inside dial to line up with shaft.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Philip from The Villages, FL
- Parts Used:
- WE01X20580
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Door handle had broken off
Replacing the door handle was a "snap" literally. All I needed to do was remove the handle from its plastic wrap; line up the inserts on the handle with the holes in the door and snap it in place. It was that simple.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Erin from Tucson, AZ
- Parts Used:
- WH01X10060
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
broken knob
The old knob broke off & was no longer able to turn the pin to start the dryer. I simply slid the new knob onto the pin & it worked like new.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Sara from Destin, FL
- Parts Used:
- WH01X10060
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Pliers
The knob broke
Took the knob and clip off the dryer and stuck the knew knob on!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Joseph from South Weber, UT
- Parts Used:
- WE4M519
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver
Rotary switch went bad
UNPLUG DRYER>>> screws removed from top panel, removed wires, removed switch, reverse order...fin! EASY
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Doug from Hollandale, MS
- Parts Used:
- WE4M519
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
rotary start switch would not work
I removed the screws to the panel holding the start switch. The panel then opens to view the start switch. Using my hand I disconnected the start switch which were three quick disconnects. The switch was easily removed. I then put new switch in and plugged wires to it,closed cover and screwed it on. Anyone could do this.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Larry from Wilmington, NC
- Parts Used:
- WE03X37318
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
High Pitch Sqeaking durng dryer operation
Replaced drum bearing part and white slides.The problem was that it was not the drum slide support. It appears to be the the drum rear bearing of whch I am now ordering. The bearing replacement is a little more difficult, but I have taken this on as a challenge
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Rich from Columbus, OH
- Parts Used:
- WE4M519
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Dryer would turn-on intermittently
Replaced power switch
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Daniel from Maryville, TN
- Parts Used:
- WH01X10060
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Pliers
Broken knob
Used pliers to remove old clip. Installed new clip and knob. Very easy.
Was this instruction helpful to you?
Thank you for voting!