DBXR463EB2CC General Electric Dryer - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- JOE from BROOMALL, PA
- Parts Used:
- WE4M519
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Pliers, Screw drivers
Dryer would not come on
Removed back top of dryer and popped switch out removed one wire at a time and connected to new switch then popped in the new switch and turned until it snapped in. Put cover back on and knob plugged in and worked like new 5 minute job saved paying someone to come out.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- stephen from Lake Lure, NC
- Parts Used:
- WE4M519
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
spring loaded start switch stopped.
removed 4 screws from top of control panel. pulled 3 knobs off. removed face cover. unplugged damaged unit. twisted unit to right and removed. installed new unit. plugged in wiring. replaced panel. replaced screws and knobs.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Dave from Wallingford, CT
- Parts Used:
- WE4M137
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Pliers, Screw drivers
Dryer would shut off on heat dry after a couple of minutes. I could feel the heat working. It would only continue to run on fluff/no heat
Pulled the drum an found spade clip burned on wire. Hi limit Thermostat crumbled/ broke while pulling spade clip so I trimmed back the wire, cleaned the spade clip and soldered the wire back on. Isolated the other thermostats in the system and tested for resistance. Reassembled dryer.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Jacquelin from The Villages, FL
- Parts Used:
- WE4M519
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 15 - 30 mins
switch stopped working
Took the front plate of the top of the dryer and then tried to fit the new switch. Unfortunately as there were no instructions on how to fit it my husband took the switch off the backing plate, and then realised his mistake. So he had to order another one. When that arrived it took all of 5 minutes to fit. It was an expensive and unnecessary mistake.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Donna from Vista, CA
- Parts Used:
- WE05X20431
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Light bulb blew out inside the dryer
Screwed the light bulb into the socket (duh)
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Pat from Kingsport, TN
- Parts Used:
- WE4M519
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Pliers, Screw drivers
Dryer start switch wouldnt work.
Turned breaker off in electrical panel. First removed all knobs.Removed four screws and removed panel.Removed wires from terminals and switch twisted off. Installed new switch,replaced wires on terminals.Put panel back in place with four screws,then replaced knobs.Turned breaker back on and started dryer with start switch,worked great.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- elbert from nunnelly, TN
- Parts Used:
- WE4M519
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
would not turn on at all
used the allen wrench to take off the cover disconnected the three wires twisted off the old switch put on the new one connected the wires back put the back cover on started the dryer up and i was all done.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Betty from Mineral, VA
- Parts Used:
- WE4M519
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Pliers
starter switch stopped working
removed three screws from face panel and removed three wires from starter switch and put them on new starter switch. Took old switch out and put in new and reassembled the face plate.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Debbie from Va Beach, VA
- Parts Used:
- WE4M519
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
Switch stuck in the ON position
Followed other people's postings. This really is a simple at home repair.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- D J from Zwolle, LA
- Parts Used:
- WE4M519
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Pliers
Dryer on switch did not work
Ordered and replaced the starter switch. Ordering was easy, just entered the model # and got a diagram of the dryer, selected the started switch and place the order. The switch arrived a few days later. It was the right switch and installation was easy. Dryer is working fine.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Anthony from Nesquehoning, PA
- Parts Used:
- WE4M519
- Difficulty Level:
- Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Pliers, Screw drivers
Start switch did not work
I pulled all the knobs, removed screws and tilted the faceplate, unplugged 3 wires, twisted the old switch to unlock it, twisted the new switch in and guessed where to install the 3 wires because the switch from PartSelect was different. After two attempts at placing the wires on the connectors, the dryer works however it shuts off at a different switch position.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Phil from Towaco, NJ
- Parts Used:
- WE4M519
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers
Dryer would not start due to defective switch
The biggest challenge was figuring out how to remove the defective starter switch. By searching the internet I found someone describing the same problem and that you had to turn in counter-clockwise to remove it.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- George from Lynchburg, VA
- Parts Used:
- WE03X37318
- Difficulty Level:
- Easy
- Total Repair Time:
- More than 2 hours
- Tools:
- Nutdriver, Screw drivers, Socket set
Drum squeaked and occassionally would not turn, even though the motor ran.
I ordered and replaced the front and rear bearings, including the slides that go on the front bearing. Most of this was un-necessary; replacing the slides would have been sufficient, and much easier to do. Two of the old slides were worn completely away.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Alfred from Euless, TX
- Parts Used:
- WE4M519
- Difficulty Level:
- Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
The dryer stopped working.
I pulled the panel off of the dryer, screwed the part back on the correct wires, replaced the panel.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- derrick from gansevoort, NY
- Parts Used:
- WE4M519
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
dryer wouldn't run
very simple , unplug dryer and unhook the back of the top of dryer using a screwdriver on 6 screws. unhook clip to the rotary starter switch and unhook the three pronged plugs that go to the starter switch. replace new one that snaps into place, plug back in the three wires. screw the back of the dryer back on and your done. 6 minute job that saves you 40-50+ dollars for a repair man plus the extra money they mark up the parts
Was this instruction helpful to you?
Thank you for voting!